-
ATmega32 Development Board
The ATmega32 Development Board is a low-cost Atmel AVR development kit based on the ATmega32 microcontroller. It provides the essential interface circuits for the microcontroller, making it an ideal choice for undergraduate laboratories, hobbyists, and beginners.
Features:
- Microcontroller: ATmega32A with a 16 MHz external crystal for reliable high-speed performance.
- USB Interface: Integrated CH340G for direct PC connectivity, programming, and serial debugging.
- Real-Time Clock: On-board DS3231 RTC with battery backup for high-precision timekeeping.
- External Memory: 24C08 (1K) Serial EEPROM via I2C for nonvolatile data storage and logging.
- Visual Feedback: Includes three programmable LEDs, a power indicator, and dedicated RX/TX status LEDs.
- Connectivity: Full breakout of all 40 pins via headers, plus a dedicated 6-pin ICSP port for external programmers.
- Utility: An on-board hardware reset button and a programmable user switch (connected to PB4) for interactive testing.
500.00 EGPIn stock
ATmega32 Development Board
500.00 EGP -
ARM STM32F401 Black Pill Breakout Board
Small handy board on which you can plug your Black Pill development board with screw terminals to get much easier to the GPIO pins.
Features :
- All Black Pill pins are provided to 3.5mm pitch screw clamp terminals for easy access.
- Screw terminals are clearly silkscreen labeled (top and bottom) to clarify the connection.
- Four (Ø 3mm) mounting holes for easy installation.
- Dimensions: 89 x 60 x 12 mm.
100.00 EGPIn stock
ARM STM32F401 Black Pill Breakout Board
100.00 EGP -
5V/3A DC-DC Buck Converter Module (LM2596)
A compact DC-DC Buck Converter based on LM2596, designed as a direct 7805 replacement. It offers higher efficiency, a wide input range (7–40V), and up to 3A output current.
Features :
- Direct 7805 Replacement: Pin-compatible with standard 7805 linear regulator (IN, GND, OUT).
- High Current Output: Supports up to 3A continuous load current, much higher than the 7805 (1A max).
- Wide Input Voltage Range: Operates from 7V to 40V DC, offering greater flexibility compared to linear regulators.
- High Efficiency: Up to 90% conversion efficiency, significantly reducing heat generation.
- Compact Size: Miniature PCB design for easy integration in projects with limited space.
- Low Heat Dissipation: Minimal power loss thanks to switching regulator technology, eliminating the need for bulky heatsinks.
- Stable Output: Provides regulated 5V output suitable for powering microcontrollers, sensors, and other digital circuits.
- Dimensions(LXWXH): 23 X19 X15 mm
50.00 EGPIn stock
-
12V/3A DC-DC Buck Converter Module (LM2596)
A compact DC-DC Buck Converter based on LM2596, designed as a direct 7812 replacement. It offers higher efficiency, a wide input range (14–40V), and up to 3A output current.
Features :
- Direct 7812 Replacement: Pin-compatible with standard 7812 linear regulator (IN, GND, OUT).
- High Current Output: Supports up to 3A continuous load current, much higher than the 7812 (1A max).
- Wide Input Voltage Range: Operates from 14V to 40V DC, offering greater flexibility compared to linear regulators.
- High Efficiency: Up to 90% conversion efficiency, significantly reducing heat generation.
- Compact Size: Miniature PCB design for easy integration in projects with limited space.
- Low Heat Dissipation: Minimal power loss thanks to switching regulator technology, eliminating the need for bulky heatsinks.
- Stable Output: Provides regulated 12V output suitable for powering microcontrollers, sensors, and other digital circuits.
- Dimensions(LXWXH): 23 X19 X15 mm.
50.00 EGPIn stock
-
8-Channel Non-Isolated Positive Triggered Relay Module (RM8VE)
8-Channel 5V relay module with wide 5–40V input range, LM2576 power regulation, ULN2803 driver, and screw terminals for easy wiring.
Features :
- 8-Channel relay module using T73 relays (rated 10A for resistive loads; recommended ≤ 5A for inductive loads).
- Wide input voltage range: 5V to 40V selectable via 3-pin jumper.
- 5–7V mode: Direct input to relays.
- 7–40V mode: Onboard LM2576 buck converter outputs stable 5V.
- Relay coil voltage: 5V for all channels.
- Compatible trigger signal range: 3V to 24V.
- Integrated ULN2803 driver IC with built-in flyback diodes for relay protection.
- Additional reverse polarity protection diode on power input.
- Each relay has LED indicator for status visualization.
- Output terminals: 3-pin screw connectors (NC, COM, NO) per relay.
- Input & power via 10-pin screw terminal (2 power pins + IN1 to IN8).
- High-quality PCB with white silkscreen legend for easy wiring identification.
- Four mounting holes (Ø 3.5 mm) for secure installation.
250.00 EGPIn stock
-
1-Channel Isolation Module
1-channel opto-isolated module suitable for voltage level converting.
Features :
- Two selectable Input control signal ranges (3-12V and 9-24V).
- Output signal range: 3-24V.
- LED indicator for each input.
- Dedicated 2-pin screw clamp terminal for each input and output.
- Output can drive high or low-triggered load.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 50 X 23 X 17mm.
40.00 EGPIn stock
1-Channel Isolation Module
40.00 EGP -
2-Channel Isolation Module
2-channel opto-isolated module suitable for voltage level converting.
Features :
- Two selectable Input control signal ranges (3-12V and 9-24V).
- Output signal range: 3-24V.
- LED indicator for each input.
- Dedicated 2-pin screw clamp terminal for each input and output.
- Output can drive high or low-triggered load.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 50 X 50 X 17mm.
70.00 EGPIn stock
2-Channel Isolation Module
70.00 EGP -
8-Channel Serial Relay Module
SRM8 is an 8-channel relay module designed to allow expanding microcontroller I/O pins. SRM8 is based on the 8-bit shift register 74595 IC. It supports 8 output relays while using only three I/Os. SRM8 can be daisy-chained to further extend the outputs to theoretically an infinite number while still using the same three microcontroller I/O pins. SRM8 module can be supplied from a wide range of voltages (5-40V). The input control signals are Digital Input (DI), Clock (CK), and Load (LD). Every time the shift register Clock input receives a low to high transition it accepts the data input value to bit0 and shifts the internal register data by one bit. Thus, 8 clock pulses are required to get one-byte data from the microcontroller. Finally, a latch pulse is required to load all internal shift register data to parallel outputs (Relays). This control sequence can be performed using a hardware-implemented SPI or a few lines of written code.
Features:
- Supports: 8-channel output relays.
- Protocol: SPI.
- Wide operating voltage range: 5-40V (two selectable ranges).
- Input signals (TTL): Data Input (DI), Clock (CK), and Load (LD).
- Output signals (TTL): Data Output (DO), Clock (CK), and Load (LD).
- Power-on relay status is OFF (a reset operation is auto-applied up on power on).
- Green LED for power indication.
- Red LED indicator for each output relay.
- Both normal open and normal close terminals are available.
- Reverse polarity protection for power input.
- Input and output signals are available via screw clamp terminals as well as pin headers for flexibility.
- SRM8 module can be daisy-chained to obtain a large number of relay outputs.
- The power connector is duplicated to facilitate the daisy chain board-to-board power connection of up to 16 modules, To connect more SRM8 modules use external wiring.
- Mounting: Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 207 X 45 X 18mm.
350.00 EGPIn stock
8-Channel Serial Relay Module
350.00 EGP -
7A/4-Channel Solid State Relay Module
Features:
- Number of supported channels: 4 independent channels.
- Input signal range: DC 3-30V.
- AC switching voltage: AC 24-250V.
- AC switching device: BTA16-600B.
- Maximum load current 7 amperes.
- A proper heatsink is used for overheating dissipation.
- All channels are opto-isolated.
- Each output has its own fuse for overcurrent protection.
- Each output has an AC snubber circuit (RC+varistor) for suppressing voltage spikes that arise from inductive loads.
- Input signals have reverse polarity protection.
- LED indicator for each input.
- Four (Ø 3.5 mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket (optional).
- Dimensions: 198 X 72 X 30 mm.
500.00 EGPIn stock
7A/4-Channel Solid State Relay Module
500.00 EGP -
5A/4-Channel Solid State Relay Module
Features:
- Number of supported channels: 4 independent channels.
- Input signal range: DC 3-30V.
- AC switching voltage: AC 24-250V.
- AC switching device: BTA16-600B.
- Maximum load current 5 Ampere.
- A proper heatsink is used for overheating dissipation.
- All channels are opto-isolated.
- Each output has its own fuse for overcurrent protection.
- Each output has an AC snubber circuit (RC+Varistor) for suppressing voltage spikes that arise from inductive loads.
- Input signals have reverse polarity protection.
- LED indicator for each input.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 198 X 72 X 22mm.
450.00 EGPIn stock
5A/4-Channel Solid State Relay Module
450.00 EGP -
ARM Development Kit (Panda+)
Panda+ kit is an ARM development kit based on Black Pill module which supports 32-bit ARM Cortex-M4 microprocessor STM32F401RCT6.
This price includes only Panda+ kit without accessories. To add more accessories please click below.
950.00 EGPIn stock
ARM Development Kit (Panda+)
950.00 EGP -
8-Channel USB-Controlled Relay Module
RM8U is an 8-channel USB-controlled relay module. It can be used to control electrical devices remotely from a PC over a USB port such as lamps, motors, and locks. RM8U features a wide operating voltage range (9-40V) and supports serial communication baud rate speeds starting from 2400 up to 115200 bps. RM8U module is well protected, filtered, and fully isolated.
Features:
- Supports Windows XP, 7, 10, and 11.
- Supports 8 relay outputs.
- Wide operating voltage range: 9~40 DCV.
- Control: Serial communication.
- Driver: CH340.
- Supported baud rates: 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, 76800, and 115200.
- Interface: USB type B connector.
- Simple control protocol: Just two-character commands.
- All outputs are optically isolated.
- Both normally open and normally close relay contacts are available.
- Reverse polarity protection.
- On-board DC power filter.
- Power LED indicator.
- Serial communication LED status.
- LED indicator for each relay.
- Mounting: Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 214 X 55 X 21mm.
550.00 EGPIn stock
8-Channel USB-Controlled Relay Module
550.00 EGP -
4-Channel USB-Controlled Relay Module
RM4U is a 4-channel USB-controlled relay module. It can be used to control electrical devices remotely from a PC over a USB port such as lamps, motors, and locks. RM4U features a wide operating voltage range (9-40V) and supports serial communication baud rate speeds starting from 2400 up to 115200 bps. RM4U module is well protected, filtered, and fully isolated.
Features:
- Supports Windows XP, 7, 10, and 11.
- Supports 4 relay outputs.
- Wide operating voltage range: 9~40 DCV.
- Control: Serial communication.
- Driver: CH340.
- Supported baud rates: 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, 76800, and 115200.
- Interface: USB type B connector.
- Simple control protocol: Just two-character commands.
- All outputs are optically isolated.
- Both normally open and normally close relay contacts are available.
- Reverse polarity protection.
- On-board DC power filter.
- Power LED indicator.
- Serial communication LED status.
- LED indicator for each relay.
- Mounting: Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 144 X 55 X 21mm.
450.00 EGPIn stock
4-Channel USB-Controlled Relay Module
450.00 EGP -
2-Channel USB-Controlled Relay Module
RM2U is a 2-channel USB-controlled relay module. It can be used to control electrical devices remotely from a PC over a USB port such as lamps, motors, and locks. RM2U features a wide operating voltage range (9-40V) and supports serial communication baud rate speeds starting from 2400 up to 115200 bps. RM2U module is well protected, filtered, and fully isolated.
Features:
- Supports Windows XP, 7, 10, and 11.
- Supports two relay outputs.
- Wide operating voltage range: 9~40 DCV.
- Control: Serial communication.
- Driver: CH340.
- Supported baud rates: 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, 76800, and 115200.
- Interface: USB type B connector.
- Simple control protocol: Just two-character commands.
- All outputs are optically isolated.
- Both normally open and normally close relay contacts are available.
- Reverse polarity protection.
- On-board DC power filter.
- Power LED indicator.
- Serial communication LED status.
- LED indicator for each relay.
- Mounting: Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 100 X 55 X 21mm.
400.00 EGPIn stock
2-Channel USB-Controlled Relay Module
400.00 EGP -
6-Channel Wireless Relay Module ESP-12F (RM6W)
The RM6W is a 6-channel Wi-Fi module based on the ESP-12F module which is based on the ESP8266 chip from Espressif. The ESP-12F includes 4MB of flash and supports 802.11b/g/n Wi-Fi SOC. The ESP-12F can be programmed serially via the 4-pin header. The card is well-protected, filtered, and easy to install. The RM6W outputs can drive loads up to 10A (resistive load).
Features:
- Based on ESP-12F Wi-Fi module.
- On-board 3.3V regulator AMS1117-3.3V.
- Power input is filtered for noise reduction.
- Green LED for power indication.
- Operating voltage DC12V.
- Six output relays with red LED indicators.
- Both normal open and normal close terminals are available.
- Output terminals are available through a 5mm 2-pin K128 screw clamp.
- Easy firmware uploading using a 4-pin header ( 3.3V, Tx, Rx, GND ).
- Reset push button switch is included.
- Two yellow LEDs for Tx and Rx signal indication.
- DIN Rail mountable.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 165 X 50 X 18mm.
450.00 EGPOut of stock
-
2-Channel Wireless Relay Module ESP-12F (RM2W)
The RM2W is a 2-channel Wi-Fi module based on the ESP-12F module which is based on the ESP8266 chip from Espressif. The ESP-12F includes 4MB of flash and supports 802.11b/g/n Wi-Fi SOC. The ESP-12F can be programmed serially via the 4-pin header. The card is well-protected, filtered, and easy to install. The RM2W outputs can drive loads up to 10A (resistive load).
Features:
- Based on ESP-12F Wi-Fi module.
- On-board 3.3V regulator AMS1117-3.3V.
- Power input is filtered for noise reduction.
- Green LED for power indication.
- Operating voltage DC12V.
- Two output relays with red LED indicators.
- Both normal open and normal close terminals are available.
- Output terminals are available through a 5mm 2-pin K128 screw clamp.
- Easy firmware uploading using a 4-pin header ( 3.3V, Tx, Rx, GND ).
- Reset push button switch is included.
- Two yellow LEDs for Tx and Rx signal indication.
- DIN Rail mountable.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 98 X 50 X 18mm.
300.00 EGPOut of stock
-
4-Channel Wireless Relay Module ESP-12F (RM4W)
The RM4W is a 4-channel Wi-Fi module based on the ESP-12F module which is based on the ESP8266 chip from Espressif. The ESP-12F includes 4MB of flash and supports 802.11b/g/n Wi-Fi SOC. The ESP-12F can be programmed serially via the 4-pin header. The card is well-protected, filtered, and easy to install. The RM4W outputs can drive loads up to 10A (resistive load).
Features:
- Based on ESP-12F Wi-Fi module.
- On-board 3.3V regulator AMS1117-3.3V.
- Power input is filtered for noise reduction.
- Green LED for power indication.
- Operating voltage DC12V.
- Four output relays with red LED indicators.
- Both normal open and normal close terminals are available.
- Output terminals are available through a 5mm 2-pin K128 screw clamp.
- Easy firmware uploading using a 4-pin header ( 3.3V, Tx, Rx, GND ).
- Reset push button switch is included.
- Two yellow LEDs for Tx and Rx signal indication.
- DIN Rail mountable.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 130 X 50 X 18mm.
400.00 EGPOut of stock
-
8-Channel Wireless Relay Module nRF24L01+ (RM8N)
The RM8N is an 8-channel wireless relay module based on the nRF24L01+ chip from Nordic Semiconductor. The nRF24L01 module is designed to operate in the global 2.4GHz ISM frequency band and uses GFSK modulation to transmit data. The card is well-protected, filtered, and easy to install. RM8N outputs can drive loads up to 10A (resistive loads).
Features:
- Based on nRF24L01+ module.
- On-board 3.3V,5V regulator.
- Power input is filtered for noise reduction.
- LED for power indication.
- Operating voltage DC12V.
- Eight output relays with red LED indicators.
- Both normal open and normal close terminals are available.
- Relay outputs are available through 5mm 2-pin K128 screw clamp terminals.
- Easy configuration and test.
- Reset push button switch is included.
- DIN Rail mountable.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 196 X 50 X 18mm.
500.00 EGPIn stock
-
4-Channel Wireless Relay Module nRF24L01+ (RM4N)
The RM4N is a 4-channel wireless relay module based on the nRF24L01+ chip from Nordic Semiconductor. The nRF24L01 module is designed to operate in the global 2.4GHz ISM frequency band and uses GFSK modulation to transmit data. The card is well-protected, filtered, and easy to install. RM4N outputs can drive loads up to 10A (resistive loads).
Features:
- Based on nRF24L01+ module.
- On-board 3.3V,5V regulator.
- Power input is filtered for noise reduction.
- LED for power indication.
- Operating voltage DC12V.
- Four output relays with red LED indicators.
- Both normal open and normal close terminals are available.
- Relay outputs are available through 5mm 2-pin K128 screw clamp terminals.
- Easy configuration and test.
- Reset push button switch is included.
- DIN Rail mountable.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 132 X 50 X 18mm.
350.00 EGPIn stock
-
2-Channel Wireless Relay Module nRF24L01+ (RM2N)
The RM2N is a 2-channel wireless relay module based on the nRF24L01+ chip from Nordic Semiconductor. The nRF24L01 module is designed to operate in the global 2.4GHz ISM frequency band and uses GFSK modulation to transmit data. The card is well-protected, filtered, and easy to install. RM2N outputs can drive loads up to 10A (resistive loads).
Features:
- Based on nRF24L01+ module.
- On-board 3.3V,5V regulator.
- Power input is filtered for noise reduction.
- LED for power indication.
- Operating voltage DC12V.
- Two output relays with red LED indicators.
- Both normal open and normal close terminals are available.
- Relay outputs are available through 5mm 2-pin K128 screw clamp terminals.
- Easy configuration and test.
- Reset push button switch is included.
- DIN Rail mountable.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 100 X 50 X 18mm.
280.00 EGPIn stock
-
Serial TTL to Wireless nRF Module SNM-H
SNM-H module is a smart serial USB (H-type connector) to wireless module based on the nRF24L01+ from Nordic Semiconductor and uses the controller ATMEGA8.
The nRF24L01+ module is designed to operate in the global 2.4GHz ISM frequency band and uses GFSK modulation to transmit data.
ATMEGA8 microcontroller comes pre-programmed to support RMxN relay modules protocol. However, the user can program ATMEGA8 microcontroller with other firmware.
SNM-H module uses a CH340 chip as a USB to Serial converter.
Features:
- Compatible with the protocol of RMxN wireless relay module.
- USB interface: USB type H connector.
- Driver: CH340.
- Baud rate: 115200.
450.00 EGPOut of stock
Serial TTL to Wireless nRF Module SNM-H
450.00 EGP -
Serial USB-B to Wireless nRF Module (SNM-B)
SNM-B module is a smart serial USB (B-type connector) to wireless module based on the nRF24L01+ from Nordic Semiconductor and uses the controller ATMEGA8.
The nRF24L01+ module is designed to operate in the global 2.4GHz ISM frequency band and uses GFSK modulation to transmit data.
ATMEGA8 microcontroller comes pre-programmed to support RMxN relay modules protocol. However, the user can program ATMEGA8 microcontroller with other firmware.
SNM-B module uses a CH340 chip as a USB to Serial converter.
Features:
- Compatible with the protocol of RMxN wireless relay module.
- USB interface: USB type B connector.
- Driver: CH340.
- Baud rate: 115200.
450.00 EGPOut of stock
Serial USB-B to Wireless nRF Module (SNM-B)
450.00 EGP -
Serial USB-A to Wireless nRF Module (SNM-A)
SNM-A module is a smart serial USB (A-type connector) to wireless module based on the nRF24L01+ from Nordic Semiconductor and uses the controller ATMEGA8.
The nRF24L01+ module is designed to operate in the global 2.4GHz ISM frequency band and uses GFSK modulation to transmit data.
ATMEGA8 microcontroller comes pre-programmed to support RMxN relay modules protocol. However, the user can program ATMEGA8 microcontroller with other firmware.
SNM-A module uses a CH340 chip as a USB to Serial converter.
Features:
- Compatible with the protocol of RMxN wireless relay module.
- USB interface: USB type A connector.
- Driver: CH340.
- Baud rate: 115200.
450.00 EGPOut of stock
Serial USB-A to Wireless nRF Module (SNM-A)
450.00 EGP -
4 Port USB 2.0 Hub
This USB hub has four USB 2.0 ports each with a max total transmission speed of up to 480 MBps. All four ports are powered through the USB-B cable.
This hub is great for giving your laptop or computer a few more plug-in options, no adapter is required.Features:
- Number of ports: 4.
- no adapter is required.
- PC interface: USB type B.
- USB device interface: USB type A.
- Output: 100mA MAX.
- Two (Ø 3.5mm) mounting holes for easy installation.
80.00 EGPIn stock
4 Port USB 2.0 Hub
80.00 EGP -
Arduino Uno Breakout Board
Arduino Uno Breakout Board.
135.00 EGPIn stock
Arduino Uno Breakout Board
135.00 EGP -
Real Time Clock Module (DS3231 & 4K Memory 24C32)
This RTC module is based on the clock chip DS1307 that provides seconds, minutes, hours, day, date, month, and year information.
Features :
- Operating voltage 5V.
- Supports the 24-hour or 12-hour format with an AM/PM indicator.
- Interface: I2C.
- On-board 4K I2C serial EEPROM.
- On-board CR2032 3V lithium battery.
- Two (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 34 X 24 X 10mm.
140.00 EGPIn stock
-
Real Time Clock Module (DS1307 & 4K Memory 24C32)
This RTC module is based on the clock chip DS1307 that provides seconds, minutes, hours, day, date, month, and year information.
Features :
- Operating voltage 5V.
- Supports the 24-hour or 12-hour format with an AM/PM indicator.
- Interface: I2C.
- On-board 4K I2C serial EEPROM.
- On-board CR2032 3V lithium battery.
- Two (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 36 X 24 X 10mm.
75.00 EGPIn stock
-
1-Channel Active High Relay Module (24V) RM124
1-Channel relay module (24V) up to 10A rated current directly interfaced to microcontroller or TTL logic.
40.00 EGPIn stock
-
6-Channel DC Power Distributor
6-Channel DC power distributor module.
Features :
- Operating voltage: 5~48 DCV.
- Maximum output current: 10A/Channel.
- Protection fuse for each channel.
- Green LED indicator for input voltage.
- Red LED indicator for each output voltage.
- 100nF filter capacitor for each output channel.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimension: 119 X 73 X 19mm.
140.00 EGPIn stock
6-Channel DC Power Distributor
140.00 EGP -
30A Current Sensor Module (ACS712)
30A Current Sensor Module (ACS712).
Features:
- Operating voltage: 5V.
- Green LED for power indication.
- Input interface 7.5mm screw clamp terminal.
- Power and output signal interface: 2.54mm male pin header.
- Maximum current: 30A.
- One (Ø 3.5mm) mounting hole for easy installation.
- Dimension: 34 X 15 X 14mm.
100.00 EGPIn stock
30A Current Sensor Module (ACS712)
100.00 EGP -
20A Current Sensor Module (ACS712)
20A Current Sensor Module (ACS712).
Features:
- Operating voltage: 5V.
- Green LED for power indication.
- Input interface 5.08mm screw clamp terminal.
- Power and output signal interface: 2.54mm male pin header.
- Maximum current: 20A.
- Dimension: 30 X 13 X 12mm.
90.00 EGPIn stock
20A Current Sensor Module (ACS712)
90.00 EGP -
5A Current Sensor Module (ACS712)
5A Current Sensor Module (ACS712).
Features:
- Operating voltage: 5V.
- Green LED for power indication.
- Input interface 5.08mm screw clamp terminal.
- Power and output signal interface: 2.54mm male pin header.
- Maximum current: 5A.
- Dimension: 30 X 13 X 12mm.
80.00 EGPIn stock
5A Current Sensor Module (ACS712)
80.00 EGP -
I²C Serial EEPROM Module 24CXX
I²C Serial EEPROM Module 24CXX.
Features:
- Operating voltage: 5V.
- Green LED for power indication.
- Interface: 2.54mm male pin header.
- One (Ø 3.5mm) mounting hole for easy installation.
- Breadboard-friendly module.
- Dimension: 22 X 10 X 8mm.
25.00 EGP – 50.00 EGPOut of stock
I²C Serial EEPROM Module 24CXX
25.00 EGP – 50.00 EGP -
4-Channel USB/RS232 Hub Converter
4-Channel USB/RS232 Hub Converter.
Features:
- No of channels: 4.
- USB interface: type B.
- RS232 interface: DB9 male + pin header.
- Driver: CH340.
- Signals per channel: RX, TX, DTR, and DSR.
- USB speed: high speed.
- Maximum transfer rate: 1Mbps.
- Operating temperature: (-40….85˚C).
- Green LED for power indication.
- Two red LEDs for serial communication activity RX, Tx for each channel.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 185 x 45 x 15mm.
450.00 EGPIn stock
4-Channel USB/RS232 Hub Converter
450.00 EGP -
IC Package Converter (QFP32-0.8mm/DIP32-600mil)
IC Package Converter (QFP32-0.8mm/DIP32-600mil).
15.00 EGPIn stock
-
IC Package Converter (QFP64-0.8mm/DIP64-1000mil)
IC Package Converter (QFP64-0.8mm/DIP64-1000mil).
25.00 EGPIn stock
-
IC Package Converter (SOIC4/DIP4)
IC Package Converter (SOIC4/DIP4).
5.00 EGPIn stock
IC Package Converter (SOIC4/DIP4)
5.00 EGP -
2-Channel Opto-isolated AC Input Detector Module (ACD2)
This module detects whether AC input exists.
Features :
- Input voltage range 110-250V.
- Output voltage range 3-24V.
- Input signals can be applied through screw terminals or pin headers for flexibility.
- Four (Ø 3.5mm) mounting holes for easy installation.
- LED indicator for AC input.
- Output and power pins are broken out into a pin header for easy interfacing.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 50 X 47 X 17mm.
40.00 EGPOut of stock
-
USB to RS485 Serial Converter Module
This USB to RS485 converter is based on CH340 USB to serial IC. It provides a virtual serial port over a USB 2.0 port. Serial signals are provided in RS485 level to screw clamp terminal. Once you have installed the drivers, the module will appear as a normal serial COM port on your computer, making it compatible with most terminal programs and development environments.
Features:
- Provides virtual serial port over USB2.0 port.
- MAX487 transceiver.
- Supports Win 7, 8, 10, and 11 32/64-bit.
- B-type socket full-speed 2.0 USB interface.
- USB-powered (5V).
- Half-duplex serial mode.
- RS485 data rate up to 250 Kbps.
- Serial baud rate up to 2 Mbps.
- Up to 128 nodes on bus.
- TVS protection ±30 KV ESD.
- PTC (JZ) for overcurrent fault protection.
- 120 Ohm terminal resistor included.
- Red LED indicator for Rx and Tx signals.
- Green LED for power status.
- One (Ø 3.5mm) mounting hole for easy installation.
- Dimensions: 49 X 21 X 15 mm.
150.00 EGPOut of stock
USB to RS485 Serial Converter Module
150.00 EGP -
8-Channel Isolation Module
8-channel opto-isolated module suitable for voltage level converting.
Features :
- Two selectable Input control signal ranges (3-12V and 9-24V).
- Output signal range: 3-24V.
- LED indicator for each input.
- Dedicated 2-pin screw clamp terminal for each input and output.
- Output can drive high or low-triggered load.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 129 X 50 X 17mm.
130.00 EGPIn stock
8-Channel Isolation Module
130.00 EGP -
IC Package Converter (SOIC8/DIP8)
IC Package Converter (SOIC8/DIP8).
5.00 EGPIn stock
IC Package Converter (SOIC8/DIP8)
5.00 EGP -
IC Package Converter (TSSOP8/DIP8)
IC Package Converter (TSSOP8/DIP8).
5.00 EGPIn stock
IC Package Converter (TSSOP8/DIP8)
5.00 EGP -
IC Package Converter (SOIC20-150mil/DIP20)
IC Package Converter (SOIC20-150mil/DIP20).
10.00 EGPIn stock
-
IC Package Converter (SOIC18-150mil/DIP18)
IC Package Converter (SOIC18-150mil/DIP18).
10.00 EGPIn stock
-
IC Package Converter (SOIC16-150mil/DIP16)
IC Package Converter (SOIC16-150mil/DIP16).
10.00 EGPIn stock
-
IC Package Converter (SOIC14/DIP14)
IC Package Converter (SOIC14/DIP14).
10.00 EGPIn stock
IC Package Converter (SOIC14/DIP14)
10.00 EGP -
IC Package Converter (SOIC20-300mil/DIP20)
IC Package Converter (SOIC20-300mil/DIP20).
10.00 EGPOut of stock
-
IC Package Converter (SOIC18-300mil/DIP18)
IC Package Converter (SOIC18-300mil/DIP18).
10.00 EGPIn stock
