-
4 Axes USB-Controlled CNC Breakout Board (Spark)
Spark CNC Controller is a completely buffered USB-controlled CNC breakout board. Supports 4 axes, four inputs, three output relays, analog output 0-10V, and can be powered from 220VAC .
2,350.00 EGPOut of stock
4 Axes USB-Controlled CNC Breakout Board (Spark)
2,350.00 EGP -
6A Dual Channel Proportional Valve Driver (PD26)
PD26 is a dual-channel industrial proportional solenoid valve driver suitable for flow and pressure control.
Features :
- Operating mode: Switching.
- Operating voltage range: 18~36V.
- Maximum output power: 150W.
- Pot-adjustable output voltage range: 12~24V.
- Maximum output current: 6A.
- Two selectable input signal ranges: (0~5V) and (0~10V).
- Two selectable output reference voltages 5V and 10V (MAX 20mA).
- Reverse polarity protection.
- Over-current and short-circuit protection.
- Green LED for power indication.
- Yellow LED for each output indication.
- Red LED for each output fault status.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimension: 122 X 112 X 30mm.
1,950.00 EGP – 2,105.00 EGPIn stock
-
3A Dual Channel Proportional Valve Driver (PD23)
PD23 is a dual-channel industrial proportional solenoid valve driver suitable for flow and pressure control.
Features :
- Operating mode: Switching.
- Operating voltage range: 18~36V.
- Maximum output power: 150W.
- Pot-adjustable output voltage range: 12~24V.
- Maximum output current: 3 ampere.
- Two selectable input signal ranges: (0~5V) and (0~10V).
- Two selectable output reference voltages 5V and 10V (MAX 20mA).
- Reverse polarity protection.
- Over-current and short-circuit protection.
- Green LED for power indication.
- Yellow LED for each output indication.
- Red LED for each output fault status.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimension: 112 x 107 x 27 mm.
1,600.00 EGP – 1,755.00 EGPIn stock
-
6A Single Channel Proportional Valve Driver (PD16)
PD16 is a single-channel industrial proportional solenoid valve driver suitable for flow or pressure control.
Features :
- Operating mode: Switching.
- Operating voltage range: 18~36V.
- Maximum output power: 150W.
- Pot-adjustable output voltage range: 12~24V.
- Maximum output current: 6 ampere.
- Two selectable input signal ranges: (0~5V) and (0~10V).
- Two selectable output reference voltages 5V and 10V (MAX 20mA).
- Reverse polarity protection.
- Over-current and short-circuit protection.
- Green LED for power indication.
- Yellow LED for output indication.
- Red LED for output fault status.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimension: 122 X 82 X 30mm.
1,200.00 EGP – 1,340.00 EGPIn stock
-
Industrial 8-Channel Relay Module (12/24V) RM8D
Industrial grade 8-Channel relay module (12/24V) up to 10A rated current.
Features :
- Operating voltage: (12/24V).
- Maximum output current: 10A.
- LED indicator for each relay.
- 8-pin relay socket with clips for easy replacement.
- Two protective varistors (470V) for each relay contact (NO, NC).
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 170 X 72 X 35mm.
1,000.00 EGP – 1,120.00 EGPIn stock
-
3A Single Channel Proportional Valve Driver (PD13)
PD13 is a single-channel industrial proportional solenoid valve driver suitable for flow or pressure control.
Features :
- Operating mode: Switching.
- Operating voltage range: 18~36V.
- Maximum output power: 150W.
- Pot-adjustable output voltage range: 12~24V.
- Maximum output current: 3 ampere.
- Two selectable input signal ranges: (0~5V) and (0~10V).
- Two selectable output reference voltages 5V and 10V (MAX 20mA).
- Reverse polarity protection.
- Over-current and short-circuit protection.
- Green LED for power indication.
- Yellow LED for output indication.
- Red LED for output fault status.
- Four 3.5mm mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimension: 107 x 80 x 27 mm.
950.00 EGP – 1,080.00 EGPIn stock
-
6Axis CNC Breakout Board (VIVA+)
VIVA+ is a completely buffered CNC parallel breakout board. Supports up to 6 axes, five inputs, spindle and coolant output relays, analog output 0-10V, watchdog protection with extra output relay, and is powered from 220VAC.
VIVA+ Features :
- Completely supports MACH3 and any other soft tool that uses an LPT port.
- AC 220V input power.
- 6 axes control signals (Pulse ”PUL” and Direction “DIR”) :
- Main / Auxiliary X-axis.
- Main / Auxiliary Y-axis.
- Z-axis.
- A-axis.
- B-axis.
- C-axis.
- Control signals are TTL compatible (10mA).
- Supports five external inputs. Three inputs for axes limits (NPN proximity sensors or micro switch inputs) and two inputs for emergency stop and probe inputs (dry contact).
- All inputs are optically isolated for safety.
- Two relay outputs for spindle and coolant control (5A maximum current).
- Optional extra output relay (controlled from pin9).
- 0-10V analog output (PWM-controlled) for controlling spindle speed.
- Watchdog feature with optional relay output to ensure that all outputs are disabled during PC starting up and software program loading.
- All outputs and inputs are brought out via pluggable screw clamp connectors for flexibility.
- LED indicator for :
- Output pulse signal “PUL” (RED LED).
- Output direction signal “DIR” (Green LED).
- Output relays “spindle”, “coolant” and “watchdog” (RED LED).
- Input signals ”XL”, ”YL”, ”ZL”, ”EMR”, and ”PRB” (Yellow LED).
- Input power (RED LED).
- Dimension: 180 X 110 X 30 mm.
900.00 EGPIn stock
6Axis CNC Breakout Board (VIVA+)
900.00 EGP -
5A/8-Channel +ve Output Transistor Interface Module TP8
Opto-isolated 8-channel / 5 Ampere positive output transistor module for PLC industrial control.
Features :
- 8-channel positive output FET type transistor.
- Operating voltage range: 12-36V (for 48V output pls contact us).
- Maximum operating current: 5 ampere.
- All channels are opto-isolated for safety.
- Green LED indicator for power input.
- Yellow LED indicator for each Input.
- Red LED indicator for each output.
- Provides 3A fuse for overcurrent protection.
- DIN rail mountable plastic box enclosure.
- Dimensions: 145 X 90 X 40mm.
750.00 EGPIn stock
-
5A/8-Channel -ve Output Transistor Interface Module TN8
Opto-isolated 8-channel / 5 Ampere negative output transistor module for PLC industrial control.
Features :
- 8-channel negative output FET type transistor.
- Operating voltage range: 12-36V (for 48V output pls contact us).
- Maximum operating current: 5 ampere.
- All channels are opto-isolated for safety.
- Green LED indicator for power input.
- Yellow LED indicator for each Input.
- Red LED indicator for each output.
- Provides 3A fuse for overcurrent protection.
- DIN rail mountable plastic box enclosure.
- Dimensions: 145 X 90 X 40mm.
750.00 EGPIn stock
-
Industrial 4-Channel Relay Module (12/24V) RM4D
Industrial grade 4-Channel relay module (12/24V) up to 10A rated current.
Features :
- Operating voltage: (12/24V).
- Maximum output current: 10A.
- LED indicator for each relay.
- 8-pin relay socket with clips for easy replacement.
- Two protective varistors (470V) for each relay contact (NO, NC).
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 96 X 72 X 35mm.
600.00 EGP – 686.00 EGPIn stock
-
3A / 8-Channel +ve Output Transistor Interface Module TP8
Opto-isolated 8-channel / 3 Ampere positive output transistor module for PLC industrial control.
Features :
- 8-channel positive output FET type transistor.
- Operating voltage range: 12-36V (for 48V output pls contact us).
- Maximum operating current: 3A.
- All channels are opto-isolated for safety.
- Green LED indicator for power input.
- Yellow LED indicator for each Input.
- Red LED indicator for each output.
- Provides 3A fuse for overcurrent protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 129 X 90 X 22mm.
550.00 EGP – 660.00 EGPIn stock
-
3A / 8-Channel -ve Output Transistor Interface Module TN8
Opto-isolated 8-channel / 3 Ampere negative output transistor module for PLC industrial control.
Features :
- 8-channel negative output FET type transistor.
- Operating voltage range: 12-36V (for 48V output pls contact us).
- Maximum operating current: 3A.
- All channels are opto-isolated for safety.
- Green LED indicator for power input.
- Yellow LED indicator for each Input.
- Red LED indicator for each output.
- Provides 3A fuse for overcurrent protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 129 X 90 X 22mm.
550.00 EGP – 660.00 EGPIn stock
-
7A/4-Channel Solid State Relay Module
Features:
- Number of supported channels: 4 independent channels.
- Input signal range: DC 3-30V.
- AC switching voltage: AC 24-250V.
- AC switching device: BTA16-600B.
- Maximum load current 7 Ampere.
- A proper heatsink is used for overheating dissipation.
- All channels are opto-isolated.
- Each output has its own fuse for overcurrent protection.
- Each output has an AC snubber circuit (RC+Varistor) for suppressing voltage spikes that arise from inductive loads.
- Input signals have reverse polarity protection.
- LED indicator for each input.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 198 X 72 X 30mm.
500.00 EGP – 630.00 EGPIn stock
-
8-Channel Wireless Relay Module nRF24L01+ (RM8N)
The RM8N is an 8-channel wireless relay module based on the nRF24L01+ chip from Nordic Semiconductor. The nRF24L01 module is designed to operate in the global 2.4GHz ISM frequency band and uses GFSK modulation to transmit data. The card is well-protected, filtered, and easy to install. RM8N outputs can drive loads up to 10A (resistive loads).
Features:
- Based on nRF24L01+ module.
- On-board 3.3V,5V regulator.
- Power input is filtered for noise reduction.
- LED for power indication.
- Operating voltage DC12V.
- Eight output relays with red LED indicators.
- Both normal open and normal close terminals are available.
- Relay outputs are available through 5mm 2-pin K128 screw clamp terminals.
- Easy configuration and test.
- Reset push button switch is included.
- DIN Rail mountable.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 196 X 50 X 18mm.
500.00 EGP – 595.00 EGPIn stock
-
5A/4-Channel Solid State Relay Module
Features:
- Number of supported channels: 4 independent channels.
- Input signal range: DC 3-30V.
- AC switching voltage: AC 24-250V.
- AC switching device: BTA16-600B.
- Maximum load current 5 Ampere.
- A proper heatsink is used for overheating dissipation.
- All channels are opto-isolated.
- Each output has its own fuse for overcurrent protection.
- Each output has an AC snubber circuit (RC+Varistor) for suppressing voltage spikes that arise from inductive loads.
- Input signals have reverse polarity protection.
- LED indicator for each input.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 198 X 72 X 22mm.
450.00 EGP – 580.00 EGPIn stock
-
8-Channel USB-Controlled Relay Module
RM8U is an 8-channel USB-controlled relay module. It can be used to control electrical devices remotely from a PC over a USB port such as lamps, motors, and locks. RM8U features a wide operating voltage range (9-40V) and supports serial communication baud rate speeds starting from 2400 up to 115200 bps. RM8U module is well protected, filtered, and fully isolated.
Features:
- Supports Windows XP, 7, 10, and 11.
- Supports 8 relay outputs.
- Wide operating voltage range: 9~40 DCV.
- Control: Serial communication.
- Driver: CH340.
- Supported baud rates: 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, 76800, and 115200.
- Interface: USB type B connector.
- Simple control protocol: Just two-character commands.
- All outputs are optically isolated.
- Both normally open and normally close relay contacts are available.
- Reverse polarity protection.
- On-board DC power filter.
- Power LED indicator.
- Serial communication LED status.
- LED indicator for each relay.
- Mounting: Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 214 X 55 X 21mm.
550.00 EGPIn stock
8-Channel USB-Controlled Relay Module
550.00 EGP -
8-Channel Solid State Relay Module (5V) SSR805
8-Channel solid state relay module (5V) 240VAC/2A directly interfaced to microcontroller or TTL logic.
Features :
- Input signal: 5V (active high).
- Maximum output current: 2A.
- Maximum output voltage: 240VAC.
- 2 Ampere overcurrent protection fuse.
- LED indicator.
550.00 EGPIn stock
-
6-Channel Wireless Relay Module ESP-12F (RM6W)
The RM6W is a 6-channel Wi-Fi module based on the ESP-12F module which is based on the ESP8266 chip from Espressif. The ESP-12F includes 4MB of flash and supports 802.11b/g/n Wi-Fi SOC. The ESP-12F can be programmed serially via the 4-pin header. The card is well-protected, filtered, and easy to install. The RM6W outputs can drive loads up to 10A (resistive load).
Features:
- Based on ESP-12F Wi-Fi module.
- On-board 3.3V regulator AMS1117-3.3V.
- Power input is filtered for noise reduction.
- Green LED for power indication.
- Operating voltage DC12V.
- Six output relays with red LED indicators.
- Both normal open and normal close terminals are available.
- Output terminals are available through a 5mm 2-pin K128 screw clamp.
- Easy firmware uploading using a 4-pin header ( 3.3V, Tx, Rx, GND ).
- Reset push button switch is included.
- Two yellow LEDs for Tx and Rx signal indication.
- DIN Rail mountable.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 165 X 50 X 18mm.
450.00 EGP – 540.00 EGPIn stock
-
4-Channel Wireless Relay Module ESP-12F (RM4W)
The RM4W is a 4-channel Wi-Fi module based on the ESP-12F module which is based on the ESP8266 chip from Espressif. The ESP-12F includes 4MB of flash and supports 802.11b/g/n Wi-Fi SOC. The ESP-12F can be programmed serially via the 4-pin header. The card is well-protected, filtered, and easy to install. The RM4W outputs can drive loads up to 10A (resistive load).
Features:
- Based on ESP-12F Wi-Fi module.
- On-board 3.3V regulator AMS1117-3.3V.
- Power input is filtered for noise reduction.
- Green LED for power indication.
- Operating voltage DC12V.
- Four output relays with red LED indicators.
- Both normal open and normal close terminals are available.
- Output terminals are available through a 5mm 2-pin K128 screw clamp.
- Easy firmware uploading using a 4-pin header ( 3.3V, Tx, Rx, GND ).
- Reset push button switch is included.
- Two yellow LEDs for Tx and Rx signal indication.
- DIN Rail mountable.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 130 X 50 X 18mm.
400.00 EGP – 475.00 EGPIn stock
-
4-Channel USB-Controlled Relay Module
RM4U is a 4-channel USB-controlled relay module. It can be used to control electrical devices remotely from a PC over a USB port such as lamps, motors, and locks. RM4U features a wide operating voltage range (9-40V) and supports serial communication baud rate speeds starting from 2400 up to 115200 bps. RM4U module is well protected, filtered, and fully isolated.
Features:
- Supports Windows XP, 7, 10, and 11.
- Supports 4 relay outputs.
- Wide operating voltage range: 9~40 DCV.
- Control: Serial communication.
- Driver: CH340.
- Supported baud rates: 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, 76800, and 115200.
- Interface: USB type B connector.
- Simple control protocol: Just two-character commands.
- All outputs are optically isolated.
- Both normally open and normally close relay contacts are available.
- Reverse polarity protection.
- On-board DC power filter.
- Power LED indicator.
- Serial communication LED status.
- LED indicator for each relay.
- Mounting: Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 144 X 55 X 21mm.
450.00 EGPIn stock
4-Channel USB-Controlled Relay Module
450.00 EGP -
Serial TTL to Wireless nRF Module SNM-H
SNM-H module is a smart serial USB (H-type connector) to wireless module based on the nRF24L01+ from Nordic Semiconductor and uses the controller ATMEGA8.
The nRF24L01+ module is designed to operate in the global 2.4GHz ISM frequency band and uses GFSK modulation to transmit data.
ATMEGA8 microcontroller comes pre-programmed to support RMxN relay modules protocol. However, the user can program ATMEGA8 microcontroller with other firmware.
SNM-H module uses a CH340 chip as a USB to Serial converter.
Features:
- Compatible with the protocol of RMxN wireless relay module.
- USB interface: USB type H connector.
- Driver: CH340.
- Baud rate: 115200.
450.00 EGPIn stock
Serial TTL to Wireless nRF Module SNM-H
450.00 EGP -
Serial USB-B to Wireless nRF Module (SNM-B)
SNM-B module is a smart serial USB (B-type connector) to wireless module based on the nRF24L01+ from Nordic Semiconductor and uses the controller ATMEGA8.
The nRF24L01+ module is designed to operate in the global 2.4GHz ISM frequency band and uses GFSK modulation to transmit data.
ATMEGA8 microcontroller comes pre-programmed to support RMxN relay modules protocol. However, the user can program ATMEGA8 microcontroller with other firmware.
SNM-B module uses a CH340 chip as a USB to Serial converter.
Features:
- Compatible with the protocol of RMxN wireless relay module.
- USB interface: USB type B connector.
- Driver: CH340.
- Baud rate: 115200.
450.00 EGPIn stock
Serial USB-B to Wireless nRF Module (SNM-B)
450.00 EGP -
Serial USB-A to Wireless nRF Module (SNM-A)
SNM-A module is a smart serial USB (A-type connector) to wireless module based on the nRF24L01+ from Nordic Semiconductor and uses the controller ATMEGA8.
The nRF24L01+ module is designed to operate in the global 2.4GHz ISM frequency band and uses GFSK modulation to transmit data.
ATMEGA8 microcontroller comes pre-programmed to support RMxN relay modules protocol. However, the user can program ATMEGA8 microcontroller with other firmware.
SNM-A module uses a CH340 chip as a USB to Serial converter.
Features:
- Compatible with the protocol of RMxN wireless relay module.
- USB interface: USB type A connector.
- Driver: CH340.
- Baud rate: 115200.
450.00 EGPOut of stock
Serial USB-A to Wireless nRF Module (SNM-A)
450.00 EGP -
4-Channel USB/RS232 Hub Converter
4-Channel USB/RS232 Hub Converter.
Features:
- No of channels: 4.
- USB interface: type B.
- RS232 interface: DB9 male + pin header.
- Driver: CH340.
- Signals per channel: RX, TX, DTR, and DSR.
- USB speed: high speed.
- Maximum transfer rate: 1Mbps.
- Operating temperature: (-40….85˚C).
- Green LED for power indication.
- Two red LEDs for serial communication activity RX, Tx for each channel.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 185 x 45 x 15mm.
450.00 EGPIn stock
4-Channel USB/RS232 Hub Converter
450.00 EGP -
16-Channel Active High Relay Module (5-40V) RM16VE
16-Channel active high relay module (5-40V) up to 10A rated current directly interfaced to a microcontroller or TTL logic.
Features :
- Operating voltage range: 5V – 40V.
- Signal voltage range: 3V-24V (Active high).
- Max output current: 10A (Resistive load).
- Output terminals: NO/COM/NC.
- LED indicator for each output relay.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 176 X 92 X 18mm.
450.00 EGPIn stock
-
CNC Breakout Board (VIVAmini)
Complete buffered CNC parallel breakout board. Supports up to 4 axes, five inputs, spindle and coolant output relays, PWM output, and a wide power supply range of 11V ~ 24V.
450.00 EGPIn stock
CNC Breakout Board (VIVAmini)
450.00 EGP -
4-Channel Wireless Relay Module nRF24L01+ (RM4N)
The RM4N is a 4-channel wireless relay module based on the nRF24L01+ chip from Nordic Semiconductor. The nRF24L01 module is designed to operate in the global 2.4GHz ISM frequency band and uses GFSK modulation to transmit data. The card is well-protected, filtered, and easy to install. RM4N outputs can drive loads up to 10A (resistive loads).
Features:
- Based on nRF24L01+ module.
- On-board 3.3V,5V regulator.
- Power input is filtered for noise reduction.
- LED for power indication.
- Operating voltage DC12V.
- Four output relays with red LED indicators.
- Both normal open and normal close terminals are available.
- Relay outputs are available through 5mm 2-pin K128 screw clamp terminals.
- Easy configuration and test.
- Reset push button switch is included.
- DIN Rail mountable.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 132 X 50 X 18mm.
350.00 EGP – 425.00 EGPIn stock
-
2-Channel Wireless Relay Module ESP-12F (RM2W)
The RM2W is a 2-channel Wi-Fi module based on the ESP-12F module which is based on the ESP8266 chip from Espressif. The ESP-12F includes 4MB of flash and supports 802.11b/g/n Wi-Fi SOC. The ESP-12F can be programmed serially via the 4-pin header. The card is well-protected, filtered, and easy to install. The RM2W outputs can drive loads up to 10A (resistive load).
Features:
- Based on ESP-12F Wi-Fi module.
- On-board 3.3V regulator AMS1117-3.3V.
- Power input is filtered for noise reduction.
- Green LED for power indication.
- Operating voltage DC12V.
- Two output relays with red LED indicators.
- Both normal open and normal close terminals are available.
- Output terminals are available through a 5mm 2-pin K128 screw clamp.
- Easy firmware uploading using a 4-pin header ( 3.3V, Tx, Rx, GND ).
- Reset push button switch is included.
- Two yellow LEDs for Tx and Rx signal indication.
- DIN Rail mountable.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 98 X 50 X 18mm.
350.00 EGP – 420.00 EGPIn stock
-
2-Channel USB-Controlled Relay Module
RM2U is a 2-channel USB-controlled relay module. It can be used to control electrical devices remotely from a PC over a USB port such as lamps, motors, and locks. RM2U features a wide operating voltage range (9-40V) and supports serial communication baud rate speeds starting from 2400 up to 115200 bps. RM2U module is well protected, filtered, and fully isolated.
Features:
- Supports Windows XP, 7, 10, and 11.
- Supports two relay outputs.
- Wide operating voltage range: 9~40 DCV.
- Control: Serial communication.
- Driver: CH340.
- Supported baud rates: 2400, 4800, 9600, 14400, 19200, 28800, 38400, 57600, 76800, and 115200.
- Interface: USB type B connector.
- Simple control protocol: Just two-character commands.
- All outputs are optically isolated.
- Both normally open and normally close relay contacts are available.
- Reverse polarity protection.
- On-board DC power filter.
- Power LED indicator.
- Serial communication LED status.
- LED indicator for each relay.
- Mounting: Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 100 X 55 X 21mm.
400.00 EGPIn stock
2-Channel USB-Controlled Relay Module
400.00 EGP -
3A / 4-Channel +ve Output Transistor Interface Module TP4
Opto-isolated 4-channel / 3 Ampere positive output transistor module for PLC industrial control.
Features :
- 4-channel positive output FET type transistor.
- Operating voltage range: 12-36V (for 48V output pls contact us).
- Maximum operating current: 3 ampere.
- All channels are opto-isolated for safety.
- Green LED indicator for power input.
- Yellow LED indicator for each Input.
- Red LED indicator for each output.
- Provides 3A fuse for overcurrent protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 90 X 78 X 22mm.
300.00 EGP – 390.00 EGPIn stock
-
3A / 4-Channel -ve Output Transistor Interface Module TN4
Opto-isolated 4-channel / 3 Ampere negative output transistor module for PLC industrial control.
Features :
- 4-channel negative output FET type transistor.
- Operating voltage range: 12-36V (for 48V output pls contact us).
- Maximum operating current: 3 ampere.
- All channels are opto-isolated for safety.
- Green LED indicator for power input.
- Yellow LED indicator for each Input.
- Red LED indicator for each output.
- Provides 3A fuse for overcurrent protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 90 X 78 X 22mm.
300.00 EGP – 390.00 EGPIn stock
-
8-Channel Serial Relay Module
SRM8 is an 8-channel relay module designed to allow expanding microcontroller I/O pins. SRM8 is based on the 8-bit shift register 74595 IC. It supports 8 output relays while using only three I/Os. SRM8 can be daisy-chained to further extend the outputs to theoretically an infinite number while still using the same three microcontroller I/O pins. SRM8 module can be supplied from a wide range of voltages (5-40V). The input control signals are Digital Input (DI), Clock (CK), and Load (LD). Every time the shift register Clock input receives a low to high transition it accepts the data input value to bit0 and shifts the internal register data by one bit. Thus, 8 clock pulses are required to get one-byte data from the microcontroller. Finally, a latch pulse is required to load all internal shift register data to parallel outputs (Relays). This control sequence can be performed using a hardware-implemented SPI or a few lines of written code.
Features:
- Supports: 8-channel output relays.
- Protocol: SPI.
- Wide operating voltage range: 5-40V (two selectable ranges).
- Input signals (TTL): Data Input (DI), Clock (CK), and Load (LD).
- Output signals (TTL): Data Output (DO), Clock (CK), and Load (LD).
- Power-on relay status is OFF (a reset operation is auto-applied up on power on).
- Green LED for power indication.
- Red LED indicator for each output relay.
- Both normal open and normal close terminals are available.
- Reverse polarity protection for power input.
- Input and output signals are available via screw clamp terminals as well as pin headers for flexibility.
- SRM8 module can be daisy-chained to obtain a large number of relay outputs.
- The power connector is duplicated to facilitate the daisy chain board-to-board power connection of up to 16 modules, To connect more SRM8 modules use external wiring.
- Mounting: Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 207 X 45 X 18mm.
350.00 EGPIn stock
8-Channel Serial Relay Module
350.00 EGP -
2-Channel Wireless Relay Module nRF24L01+ (RM2N)
The RM2N is a 2-channel wireless relay module based on the nRF24L01+ chip from Nordic Semiconductor. The nRF24L01 module is designed to operate in the global 2.4GHz ISM frequency band and uses GFSK modulation to transmit data. The card is well-protected, filtered, and easy to install. RM2N outputs can drive loads up to 10A (resistive loads).
Features:
- Based on nRF24L01+ module.
- On-board 3.3V,5V regulator.
- Power input is filtered for noise reduction.
- LED for power indication.
- Operating voltage DC12V.
- Two output relays with red LED indicators.
- Both normal open and normal close terminals are available.
- Relay outputs are available through 5mm 2-pin K128 screw clamp terminals.
- Easy configuration and test.
- Reset push button switch is included.
- DIN Rail mountable.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 100 X 50 X 18mm.
280.00 EGP – 350.00 EGPIn stock
-
8-Channel High/Low Trigger Relay Module (24V) Opto-isolated RM824I
8-Channel 24V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.
Features :
- LED indicator for each output relay.
- Both normally open and normally close are available.
- Contact current up to 10A (Resistive load).
- Isolated/non-isolated operation mode.
- Active high/low trigger operation.
- Input signals can be applied through screw terminals or pin headers for flexibility.
- Separated screw terminal power input for relay contact ( isolated mode ).
- Reverse polarity protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 146 X 66 X 20mm.
300.00 EGPIn stock
-
8-Channel High/Low Trigger Relay Module (12V) Opto-isolated RM812I
8-Channel 12V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.
Features :
- LED indicator for each output relay.
- Both normally open and normally close are available.
- Contact current up to 10A (Resistive load).
- Isolated/non-isolated operation mode.
- Active high/low trigger operation.
- Input signals can be applied through screw terminals or pin headers for flexibility.
- Separated screw terminal power input for relay contact (isolated mode).
- Reverse polarity protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 140 X 66 X 20mm.
300.00 EGPIn stock
-
8-Channel High/Low Trigger Relay Module (5V) Opto-isolated RM805I
8-Channel 5V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.
Features :
- LED indicator for each output relay.
- Both normally open and normally close are available.
- Contact current up to 10A (Resistive load).
- Isolated/non-isolated operation mode.
- Active high/low trigger operation.
- Input signals can be applied through screw terminals or pin headers for flexibility.
- Separated screw terminal power input for relay contact (isolated mode).
- Reverse polarity protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 146 X 66 X 20mm.
300.00 EGPIn stock
-
8-Channel DC Power Distributor
8-Channel DC power distributor module.
Features :
- Operating voltage: 5~48 DCV.
- Maximum output current: 10A/Channel.
- Protection fuse for each channel.
- Green LED indicator for input voltage.
- Red LED indicator for each output voltage.
- 100nF filter capacitor for each output channel.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimension: 143 X 72 X 20mm.
175.00 EGP – 285.00 EGPIn stock
-
4-Channel Solid State Relay Module (5V) SSR405
4-Channel solid state relay module (5V) 240VAC/2A directly interfaced to microcontroller or TTL logic.
Features :
- Input signal: 5V (active high).
- Maximum output current: 2A.
- Maximum output voltage: 240VAC.
- 2 Ampere overcurrent protection fuse.
- LED indicator.
280.00 EGPIn stock
-
8-Channel Non-Isolated Positive Triggered Relay Module (RM8VE)
8-Channel 5V relay module with wide 5–40V input range, LM2576 power regulation, ULN2803 driver, and screw terminals for easy wiring.
Features :
- 8-Channel relay module using T73 relays (rated 10A for resistive loads; recommended ≤ 5A for inductive loads).
- Wide input voltage range: 5V to 40V selectable via 3-pin jumper.
- 5–7V mode: Direct input to relays.
- 7–40V mode: Onboard LM2576 buck converter outputs stable 5V.
- Relay coil voltage: 5V for all channels.
- Compatible trigger signal range: 3V to 24V.
- Integrated ULN2803 driver IC with built-in flyback diodes for relay protection.
- Additional reverse polarity protection diode on power input.
- Each relay has LED indicator for status visualization.
- Output terminals: 3-pin screw connectors (NC, COM, NO) per relay.
- Input & power via 10-pin screw terminal (2 power pins + IN1 to IN8).
- High-quality PCB with white silkscreen legend for easy wiring identification.
- Four mounting holes (Ø 3.5 mm) for secure installation.
250.00 EGPIn stock
-
6-Channel DC Power Distributor
6-Channel DC power distributor module.
Features :
- Operating voltage: 5~48 DCV.
- Maximum output current: 10A/Channel.
- Protection fuse for each channel.
- Green LED indicator for input voltage.
- Red LED indicator for each output voltage.
- 100nF filter capacitor for each output channel.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimension: 119 X 73 X 19mm.
140.00 EGP – 240.00 EGPIn stock
-
3A / 2-Channel +ve Output Transistor Interface Module TP2
Opto-isolated 2-channel / 3 Ampere positive output transistor module for PLC industrial control.
Features :
- 2-channel positive output FET type transistor.
- Operating voltage range: 12-36V (for 48V output pls contact us).
- Maximum operating current: 3A.
- All channels are opto-isolated for safety.
- Green LED indicator for power input.
- Yellow LED indicator for each Input.
- Red LED indicator for each output.
- Provides 3A fuse for overcurrent protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 90 X 53 X 22mm.
150.00 EGP – 227.50 EGPIn stock
-
3A / 2-Channel -ve Output Transistor Interface Module TN2
Opto-isolated 2-channel / 3 Ampere negative output transistor module for PLC industrial control.
Features :
- 2-channel negative output FET type transistor.
- Operating voltage range: 12-36V (for 48V output pls contact us).
- Maximum operating current: 3A.
- All channels are opto-isolated for safety.
- Green LED indicator for power input.
- Yellow LED indicator for each Input.
- Red LED indicator for each output.
- Provides 3A fuse for overcurrent protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 90 X 53 X 22mm.
150.00 EGP – 227.50 EGPIn stock
-
8-Channel Active High Relay Module (24V) RM824
8-Channel relay module (24V) up to 10A rated current directly interfaced to a microcontroller or TTL logic.
225.00 EGPIn stock
-
8-Channel Active High Relay Module (5V) RM805
8-Channel relay module (5V) up to 10A rated current directly interfaced to a microcontroller or TTL logic.
225.00 EGPIn stock
-
8-Channel Active High Relay Module (12V) RM812
8-Channel relay module (12V ) up to 10A rated current directly interfaced to a microcontroller or TTL logic.
225.00 EGPIn stock
-
4-Channel DC Power Distributor
4-Channel DC power distributor module.
Features :
- Operating voltage: 5~48 DCV.
- Maximum output current: 10A/Channel.
- Protection fuse for each channel.
- Green LED indicator for input voltage.
- Red LED indicator for each output voltage.
- 100nF filter capacitor for each output channel.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimension: 91 x 72 x 20mm.
100.00 EGP – 190.00 EGPIn stock
-
Project Work Area
FR4 PCB General project work area with DC power input and regulation.
Features :
- Double layer FR4 PCB.
- Project Kit can be powered from any general DC adaptor 8-20V thanks to an on-board 5V regulator.
- On-board reverse polarity protection.
- 15 External input via screw clamp terminals 3.5mm pitch.
- Large size work area 148 horizontal lines X 5 points, 37 X 3 vertical 5V lines, 37 X 3 vertical GND lines, 15 lines X 2 points (in addition to power rails GND, 5V, VIN).
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 118 X 108 X 20mm.
190.00 EGPIn stock
Project Work Area
190.00 EGP -
8-Channel Isolation Module
8-channel opto-isolated module suitable for voltage level converting.
Features :
- Two selectable Input control signal ranges (3-12V and 9-24V).
- Output signal range: 3-24V.
- LED indicator for each input.
- Dedicated 2-pin screw clamp terminal for each input and output.
- Output can drive high or low-triggered load.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 129 X 50 X 17mm.
100.00 EGP – 175.00 EGPIn stock
