-
DC Power Module
DC power socket adapter module suitable for breadboard with ON/OFF switch, fast blow fuse, LED indicator, and diode for reverse polarity protection.
25.00 EGPIn stock
DC Power Module
25.00 EGP -
1-Channel Relay Module (5V/12V/24V) RM1V
1-Channel relay module (5V/12V/24V) up to 10A rated current directly interfaced to microcontroller or TTL logic.
50.00 EGPIn stock
1-Channel Relay Module (5V/12V/24V) RM1V
50.00 EGP -
1-Channel Wireless Relay Module ESP-01 RM1W
1-Channel wireless relay module ( ESP-01 Wi-Fi ).
Features :
- Wireless: Wi-Fi (2X4 2.54mm female header for ESP-01S Module).
- Operating Voltage: DC5V.
- Output Rating: One relay output (Normally open and normally closed) 10A MAX (resistive load) Port pin IO0.
- Red LED for Relay status.
- Green LED for power indication.
- RST switch for reset operation.
- One (Ø 3.5mm) mounting hole for easy installation.
- Dimensions: 35 X 32 X 17mm.
65.00 EGPIn stock
-
RJ45-8 to Screw Terminal + Pin Header (Horizontal Plugging)
RJ45 8pin socket on PCB to block terminals and pin header facilitates solderless connection to RJ45 connector and is also suitable for breadboard test applications.
Features :
- RJ45 pins are routed to pin headers and screw clamp terminals.
- Both terminals are labeled according to the RJ45 pin number to which they are routed.
- Pin header pitch distance is 2.54mm.
- Screw terminal pitch distance is 3.5mm.
- Two (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 29 X 29 X 15mm.
35.00 EGPIn stock
-
RJ45 to Pin Header (Horizontal Plugging)
RJ45 socket on PCB to header suitable for breadboard test applications.
15.00 EGPIn stock
RJ45 to Pin Header (Horizontal Plugging)
15.00 EGP -
DC Power Module 9V,5V
9V battery socket with 5V regulator to pin header suitable for bread board applications.
25.00 EGPIn stock
DC Power Module 9V,5V
25.00 EGP -
8-LED Active High Module (LP8)
LP8 is an 8-bit LED display module.
Features :
- Suitable for breadboard testing.
- LEDs are active high enabled. i.e to turn a LED on apply a high logic level.
- LP8 is a common cathode module ( all negative terminals are connected together and brought out via pin header ).
- TTL compatible.
- Wide input voltage range 3V:12V.
- Compatible with our microcontroller development kits such as Eta32, and Betamini.
20.00 EGPOut of stock
-
SPDT Relay to Pin Header
SPDT 5 pin 10A relay to header module suitable for breadboard test applications.
20.00 EGPIn stock
SPDT Relay to Pin Header
20.00 EGP -
8-LED Active Low Module (LN8)
LN8 is an 8-bit LED display module.
Features :
- Suitable for breadboard testing.
- LEDs are active LOW enabled. i.e to turn a LED ON apply a low logic level.
- LN8 is a common anode module ( all positive terminals are connected together and brought out via pin header ).
- TTL compatible.
- Wide input voltage range 3V:12V.
- Compatible with our microcontroller development kits such as Eta32, and Betamini.
0.00 EGP – 20.00 EGPOut of stock
-
RJ45 to Pin Header (Vertical Plugging)
RJ45 socket on PCB to header suitable for breadboard test applications.
20.00 EGPIn stock
RJ45 to Pin Header (Vertical Plugging)
20.00 EGP -
4-Channel Relay Module (5V/12V/24V) RM4V
4-Channel relay module (5V/12V/24V) up to 10A rated current directly interfaced to microcontroller or TTL logic .
150.00 EGPIn stock
4-Channel Relay Module (5V/12V/24V) RM4V
150.00 EGP -
USB Type A Female to Pin Header
USB type A female socket on PCB to header suitable for breadboard test applications.
12.00 EGPIn stock
USB Type A Female to Pin Header
12.00 EGP -
RJ45 Side by Side Coupler With Pin Header
RJ45 side by side coupler with pin header.
38.00 EGPIn stock
-
USB Type A Male to Pin Header
USB type A male socket on PCB to header suitable for breadboard test applications.
12.00 EGPOut of stock
USB Type A Male to Pin Header
12.00 EGP -
DB9 Female to Screw Terminal + Pin Header
DB9 female socket on PCB to block terminals and pin header facilitates solderless connection to standard serial connector DB9 and is also suitable for breadboard test applications.
Features :
- DB9 pins are routed to pin headers and screw clamp terminals.
- Both terminals are labeled according to the DB9 pin number to which they are routed.
- Pin header pitch distance 2.54mm.
- Screw terminal pitch distance 3.5mm.
- Two (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 35 X 33 X 15mm.
40.00 EGPIn stock
-
ESP-01 Breakout Board
ESP-01 breakout board is suitable for breadboard applications.
10.00 EGPIn stock
ESP-01 Breakout Board
10.00 EGP -
5V/1A DC-DC Buck Converter
5V/1A DC-DC buck converter (7-40Vin). Suitable to replace 7805 for high-efficiency requirements.
25.00 EGPIn stock
5V/1A DC-DC Buck Converter
25.00 EGP -
1-Channel Opto-isolated AC Input Detector Module (ACD1)
This module detects whether AC input exists.
Features :
- Input voltage range 110-250V.
- Output voltage range 3-24V.
- Input is opto-isolated for safety.
- Four (Ø 3.5mm) mounting holes for easy installation.
- LED indicator for AC input.
- Output and power pins are broken out into a pin header for easy interfacing.
- Dimensions: 40 X 20 X 15mm.
30.00 EGPIn stock
-
RC Snubber Module
RC absorption/snubber circuit module. Suitable for relay contact protection.
30.00 EGPIn stock
RC Snubber Module
30.00 EGP -
Breadboard Power Supply Module MB102
Power supply module for breadboard applications (3.3V, 5V, and VDC).
Features :
- Input voltage range 6.5V >> 15V.
- Output voltages 3.3V, 5V, and Vin.
- Output 5V (USB type A female socket).
- Output voltages are available via screw terminal block and pin header for flexibility.
- ON/OFF switch.
- Reverse polarity protection.
- Over current protection (1A).
90.00 EGPIn stock
Breadboard Power Supply Module MB102
90.00 EGP -
3A / 8-Channel +ve Output Transistor Interface Module TP8
Opto-isolated 8-channel / 3 Ampere positive output transistor module for PLC industrial control.
Features :
- 8-channel positive output FET type transistor.
- Operating voltage range: 12-36V (for 48V output pls contact us).
- Maximum operating current: 3A.
- All channels are opto-isolated for safety.
- Green LED indicator for power input.
- Yellow LED indicator for each Input.
- Red LED indicator for each output.
- Provides 3A fuse for overcurrent protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 129 X 90 X 22mm.
550.00 EGP – 660.00 EGPIn stock
-
AC/DC Filter 3A
AC/DC power filter is a bidirectional passive Low pass filter useful in filtering the output voltages of power supplies or transformers (not line input) such as filtering output 24VAC of a transformer. For AC Line filtration use our AC Line Filter.
Features :
- Maximum operating voltage: AC250V / DC400V.
- Maximum Current: 3A.
- Cut-off frequency: 5KHz.
- Operating temperature: -40 to 85°C.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 47 X 22 X 17mm.
45.00 EGPIn stock
AC/DC Filter 3A
45.00 EGP -
L298 to Pin Header
Dual H-Bridge L298 IC driver to pin header breakout board, Suitable for DC Motor Driving or interfacing to L297 to easily build stepper motor driver.
60.00 EGPIn stock
L298 to Pin Header
60.00 EGP -
1-Channel Isolation Module
1-channel opto-isolated module suitable for voltage level converting.
Features :
- Two selectable Input control signal ranges (3-12V and 9-24V).
- Output signal range: 3-24V.
- LED indicator for each input.
- Dedicated 2-pin screw clamp terminal for each input and output.
- Output can drive high or low-triggered load.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 50 X 23 X 17mm.
40.00 EGPIn stock
1-Channel Isolation Module
40.00 EGP -
ESP12 Breakout Board
ESP8266 (ESP12) Wi-Fi module breakout board.
10.00 EGPOut of stock
ESP12 Breakout Board
10.00 EGP -
DB9 Male to Screw Terminal + Pin Header
DB9 male socket on PCB to block terminals and pin header facilitates solderless connection to standard serial connector DB9 and is also suitable for breadboard test applications.
Features :
- DB9 pins are routed to pin headers and screw clamp terminals.
- Both terminals are labeled according to the DB9 pin number to which they are routed.
- Pin header pitch distance 2.54mm.
- Screw terminal pitch distance 3.5mm.
- Two (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 35 X 33 X 15mm.
40.00 EGPIn stock
DB9 Male to Screw Terminal + Pin Header
40.00 EGP -
1-Channel Active High Relay Module (12V) RM112
1-Channel relay module (12V) up to 10A rated current directly interfaced to microcontroller or TTL logic.
40.00 EGPIn stock
-
I²C Serial EEPROM Module 24CXX
I²C Serial EEPROM Module 24CXX.
Features:
- Operating voltage: 5V.
- Green LED for power indication.
- Interface: 2.54mm male pin header.
- One (Ø 3.5mm) mounting hole for easy installation.
- Breadboard-friendly module.
- Dimension: 22 X 10 X 8mm.
25.00 EGP – 50.00 EGPIn stock
I²C Serial EEPROM Module 24CXX
25.00 EGP – 50.00 EGP -
10A AC Line Filter
AC 250V 10A EMI Filter.
Features :
- Maximum operating voltage: AC250V.
- Maximum Current: 10 Ampere.
- Cut-off frequency: 5KHz.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 60 X 30 X 30mm.
130.00 EGPIn stock
10A AC Line Filter
130.00 EGP -
16-Channel Active High Relay Module (5-40V) RM16VE
16-Channel active high relay module (5-40V) up to 10A rated current directly interfaced to a microcontroller or TTL logic.
Features :
- Operating voltage range: 5V – 40V.
- Signal voltage range: 3V-24V (Active high).
- Max output current: 10A (Resistive load).
- Output terminals: NO/COM/NC.
- LED indicator for each output relay.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 176 X 92 X 18mm.
450.00 EGPIn stock
-
4 Digits 0.56” 7-Segment Display Module 56D400
56D400 is a serial SPI 4-digit 7-segment LED display module based on MAX7219 driver. The module is 5V powered and easy to interface to Arduino board or any microcontroller. MAX7219 driver provides individual LED segment control, display ON/OFF, and brightness control.
80.00 EGP – 85.00 EGPOut of stock
4 Digits 0.56” 7-Segment Display Module 56D400
80.00 EGP – 85.00 EGP -
4-Channel High/Low Trigger Relay Module (24V) Opto-isolated RM424I
4-Channel 24V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.
Features :
- LED indicator for each output relay.
- Both normally open and normally close are available.
- Contact current up to 10A (Resistive load).
- Isolated/non-isolated operation mode.
- Active high/low trigger operation.
- Input signals can be applied through screw terminals or pin headers for flexibility.
- Separated screw terminal power input for relay contact (isolated mode).
- Reverse polarity protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 80 X 68 X 20mm.
175.00 EGPIn stock
-
3+3+2 Digits 0.36” 7-Segment Display Module 36D332
36D332 is a serial SPI 3+3+2-digit 7-segment LED display module based on MAX7219 driver. The module is 5V powered and easy to interface to Arduino board or any microcontroller. MAX7219 driver provides individual LED segment control, display ON/OFF, and brightness control.
110.00 EGP – 125.00 EGPOut of stock
3+3+2 Digits 0.36” 7-Segment Display Module 36D332
110.00 EGP – 125.00 EGP -
4-Channel Active High Relay Module (12V) RM412
4-Channel relay module (12V ) up to 10A rated current directly interfaced to a microcontroller or TTL logic.
135.00 EGPIn stock
-
Dual Channel UART Serial RS232/TTL Converter (Terminal to Terminal)
Serial UART Module converts serial RS232 to TTL signal using MAX232 IC. It can be used to interface RS232 devices like PCs and some LCDs to microcontrollers and Arduino boards. This module can be used with many microcontrollers (AVR, PIC, Intel, etc), and allows bidirectional communication (converts signals from TTL level to RS232 and from RS232 level to TTL).
Features :
- Converts signals from RS232 to TTL and vice versa.
- Compatible with many microcontrollers.
- Operating voltage: 5V.
- Supports two channels ( Two pairs of Rx, Tx).
- Red LED indicator for each transmitting signal.
- Yellow LED indicator for each receiving signal.
- Green LED for power indication.
- All Signals are provided through both pin headers and screw clamp terminals for flexibility.
- Pins are clearly labeled according to their function.
- Pin header pitch distance 2.54mm.
- Screw terminal pitch distance 3.5mm.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 55 X 35 X 12mm.
100.00 EGPIn stock
-
Photo Interrupt Module (CNA1015)
A photo interrupter sensor consists of a light-emitting element (IR LED) and a light-receiving element (phototransistor) aligned facing each other. It works by detecting light interruption when a target object comes between both elements, acting as an optical switch. This changes the output of the sensor.
Features :
- USB a wide voltage comparator LM393.
- Operating voltage: 3.3 ~ 5V.
- Active low output i.e an interruption produces a low output (LED is activated).
- Maximum output sink current: 10mA.
- 5mm slot width.
- Two (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 26 X 21 X 6mm.
35.00 EGPIn stock
Photo Interrupt Module (CNA1015)
35.00 EGP -
8-Channel High/Low Trigger Relay Module (24V) Opto-isolated RM824I
8-Channel 24V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.
Features :
- LED indicator for each output relay.
- Both normally open and normally close are available.
- Contact current up to 10A (Resistive load).
- Isolated/non-isolated operation mode.
- Active high/low trigger operation.
- Input signals can be applied through screw terminals or pin headers for flexibility.
- Separated screw terminal power input for relay contact ( isolated mode ).
- Reverse polarity protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 146 X 66 X 20mm.
300.00 EGPIn stock
-
5A/8-Channel +ve Output Transistor Interface Module TP8
Opto-isolated 8-channel / 5 Ampere positive output transistor module for PLC industrial control.
Features :
- 8-channel positive output FET type transistor.
- Operating voltage range: 12-36V (for 48V output pls contact us).
- Maximum operating current: 5 ampere.
- All channels are opto-isolated for safety.
- Green LED indicator for power input.
- Yellow LED indicator for each Input.
- Red LED indicator for each output.
- Provides 3A fuse for overcurrent protection.
- DIN rail mountable plastic box enclosure.
- Dimensions: 145 X 90 X 40mm.
750.00 EGPIn stock
-
12V/1A DC-DC Buck Converter
12V/1A DC-DC buck converter (14-40Vin). Suitable to replace 7812 for high-efficiency requirements.
25.00 EGPIn stock
12V/1A DC-DC Buck Converter
25.00 EGP -
DB9 Male to Pin Header
DB9 male socket on PCB to header suitable for breadboard test applications.
10.00 EGPIn stock
DB9 Male to Pin Header
10.00 EGP -
6Axis CNC Breakout Board (VIVA+)
VIVA+ is a completely buffered CNC parallel breakout board. Supports up to 6 axes, five inputs, spindle and coolant output relays, analog output 0-10V, watchdog protection with extra output relay, and is powered from 220VAC.
VIVA+ Features :
- Completely supports MACH3 and any other soft tool that uses an LPT port.
- AC 220V input power.
- 6 axes control signals (Pulse ”PUL” and Direction “DIR”) :
- Main / Auxiliary X-axis.
- Main / Auxiliary Y-axis.
- Z-axis.
- A-axis.
- B-axis.
- C-axis.
- Control signals are TTL compatible (10mA).
- Supports five external inputs. Three inputs for axes limits (NPN proximity sensors or micro switch inputs) and two inputs for emergency stop and probe inputs (dry contact).
- All inputs are optically isolated for safety.
- Two relay outputs for spindle and coolant control (5A maximum current).
- Optional extra output relay (controlled from pin9).
- 0-10V analog output (PWM-controlled) for controlling spindle speed.
- Watchdog feature with optional relay output to ensure that all outputs are disabled during PC starting up and software program loading.
- All outputs and inputs are brought out via pluggable screw clamp connectors for flexibility.
- LED indicator for :
- Output pulse signal “PUL” (RED LED).
- Output direction signal “DIR” (Green LED).
- Output relays “spindle”, “coolant” and “watchdog” (RED LED).
- Input signals ”XL”, ”YL”, ”ZL”, ”EMR”, and ”PRB” (Yellow LED).
- Input power (RED LED).
- Dimension: 180 X 110 X 30 mm.
900.00 EGPIn stock
6Axis CNC Breakout Board (VIVA+)
900.00 EGP -
Industrial 8-Channel Relay Module (12/24V) RM8D
Industrial grade 8-Channel relay module (12/24V) up to 10A rated current.
Features :
- Operating voltage: (12/24V).
- Maximum output current: 10A.
- LED indicator for each relay.
- 8-pin relay socket with clips for easy replacement.
- Two protective varistors (470V) for each relay contact (NO, NC).
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 170 X 72 X 35mm.
1,000.00 EGP – 1,120.00 EGPIn stock
-
3+3+2 Digits 0.56” 7-Segment Display Module 56D332
56D332 is a serial SPI 3+3+2-digit 7-segment LED display module based on MAX7219 driver. The module is 5V powered and easy to interface to Arduino board or any microcontroller. MAX7219 driver provides individual LED segment control, display ON/OFF, and brightness control.
130.00 EGP – 145.00 EGPOut of stock
3+3+2 Digits 0.56” 7-Segment Display Module 56D332
130.00 EGP – 145.00 EGP -
USB to RS485 Serial Converter Module
This USB to RS485 converter is based on CH340 USB to serial IC. It provides a virtual serial port over a USB 2.0 port. Serial signals are provided in RS485 level to screw clamp terminal. Once you have installed the drivers the module will appear as a normal serial COM port on your computer making it compatible with most terminal programs and development environments.
Features :
- Provides virtual serial port over USB2.0 port.
- MAX487 transceiver.
- Supports Win 7, 8, 10, 11 32/64 bit.
- B-type socket full-speed 2.0 USB interface.
- USB-powered (5V).
- Half duplex serial mode.
- RS485 data rate up to 250 Kbps.
- Serial baud rate up to 2Mbps.
- Up to 128 nodes on bus.
- TVS protection ±30 KV ESD.
- PTC ( JZ ) for overcurrent fault protection.
- 120 Ohm terminal resistor included.
- Red LED indicator for Rx and Tx signals.
- Green LED for power status.
- One (Ø 3.5mm) mounting hole for easy installation.
- Dimensions: 49 X 21 X 15mm.
150.00 EGPIn stock
USB to RS485 Serial Converter Module
150.00 EGP -
8 Digits 0.56” 7-Segment Display Module 56D800
56D800 is a serial SPI 8-digit 7-segment LED display module based on MAX7219 driver. The module is 5V powered and easy to interface to Arduino board or any microcontroller. MAX7219 driver provides individual LED segment control, display ON/OFF, and brightness control.
115.00 EGP – 125.00 EGPOut of stock
8 Digits 0.56” 7-Segment Display Module 56D800
115.00 EGP – 125.00 EGP -
8 Digits 36” 7-Segment Display Module 36D800
36D800 is a serial SPI 8-digit 7-segment LED display module based on MAX7219 driver. The module is 5V powered and easy to interface to Arduino board or any microcontroller. MAX7219 driver provides individual LED segment control, display ON/OFF, and brightness control.
100.00 EGP – 110.00 EGPOut of stock
8 Digits 36” 7-Segment Display Module 36D800
100.00 EGP – 110.00 EGP -
DB25 Female to Screw Terminal + Pin Header
DB25 female socket on PCB to block terminals and pin header facilitates solderless connection to standard serial connector DB25 and is also suitable for breadboard test applications.
Features :
- DB25 pins are routed to pin headers and screw clamp terminals.
- Both terminals are labeled according to the DB25 pin number to which they are routed.
- Pin header pitch distance 2.54mm.
- Screw terminal pitch distance 3.5mm.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 93 X 33 X 15mm.
70.00 EGPIn stock
-
4-Channel Opto-isolated AC Input Detector Module (ACD4)
This module detects whether AC input exists.
Features :
- Input voltage range 110-250V.
- Output voltage range 3-24V.
- Input is opto-isolated for safety.
- Four (Ø 3.5mm) mounting holes for easy installation.
- LED indicator for AC input.
- Output and power pins are broken out into a pin header for easy interfacing.
- Dimensions: 55 X 51 X 15mm.
50.00 EGPIn stock
