-
4-Channel LED Terminal
4-channel LED terminal module.
Features :
- Suitable for breadboard testing.
- LEDs are active high enabled. i.e to turn a LED on apply a high logic level.
- 1K Ohm current limiting resistor.
- TTL compatible.
- Wide input voltage range 3V:12V.
10.00 EGPIn stock
4-Channel LED Terminal
10.00 EGP -
4-Channel Opto-isolated AC Input Detector Module (ACD4)
This module detects whether AC input exists.
Features :
- Input voltage range 110-250V.
- Output voltage range 3-24V.
- Input is opto-isolated for safety.
- Four (Ø 3.5mm) mounting holes for easy installation.
- LED indicator for AC input.
- Output and power pins are broken out into a pin header for easy interfacing.
- Dimensions: 55 X 51 X 15mm.
50.00 EGPIn stock
-
4-Channel Relay Module (5V/12V/24V) RM4V
4-Channel relay module (5V/12V/24V) up to 10A rated current directly interfaced to microcontroller or TTL logic .
150.00 EGPIn stock
4-Channel Relay Module (5V/12V/24V) RM4V
150.00 EGP -
4-Channel Solid State Relay Module (5V) SSR405
4-Channel solid state relay module (5V) 240VAC/2A directly interfaced to microcontroller or TTL logic.
Features :
- Input signal: 5V (active high).
- Maximum output current: 2A.
- Maximum output voltage: 240VAC.
- 2 Ampere overcurrent protection fuse.
- LED indicator.
280.00 EGPIn stock
-
4+4 Digits 0.36” 7-Segment Display Module 36D440
36D440 is a serial SPI 4+4-digit 7-segment LED display module based on MAX7219 driver. The module is 5V powered and easy to interface to Arduino board or any microcontroller. MAX7219 driver provides individual LED segment control, display ON/OFF, and brightness control.
100.00 EGP – 110.00 EGPIn stock
4+4 Digits 0.36” 7-Segment Display Module 36D440
100.00 EGP – 110.00 EGP -
4+4 Digits 0.56” 7-Segment Display Module 56D440
56D440 is a serial SPI 4+4-digit 7-segment LED display module based on MAX7219 driver. The module is 5V powered and easy to interface to Arduino board or any microcontroller. MAX7219 driver provides individual LED segment control, display ON/OFF, and brightness control.
115.00 EGP – 125.00 EGPIn stock
4+4 Digits 0.56” 7-Segment Display Module 56D440
115.00 EGP – 125.00 EGP -
4A Step Motor Driver SD40
SD40 is an easy-to-use professional stepper motor driver, which can control a two-phase stepping motor. It’s compatible with any CNC breakout board or any micro-based control board such as Arduino boards.
Features :
- Single input power (12–40VDC).
- 4 Amps/phase maximum output motor driving current.
- 4 Selectable work current (1A, 2A, 3A, 4A).
- Optional auto idle current reduction (30%).
- Step, direction, and enable input signals are TTL
compatible. - Steps/Revolution 400, 800, 1600, 3200.
- Test mode operation.
- All controlling input signals are opto-isolated for safety.
- High-speed opto-coupler isolator on step and direction.
- Over temperature and over current protection.
- Two input LED indicators, green for power and red for fault.
- Large area heat sink.
- Dimensions: 118 X 76 X 33mm.
400.00 EGPOut of stock
4A Step Motor Driver SD40
400.00 EGP -
5A/8-Channel -ve Output Transistor Interface Module TN8
Opto-isolated 8-channel / 5 Ampere negative output transistor module for PLC industrial control.
Features :
- 8-channel negative output FET type transistor.
- Operating voltage range: 12-36V (for 48V output pls contact us).
- Maximum operating current: 5 ampere.
- All channels are opto-isolated for safety.
- Green LED indicator for power input.
- Yellow LED indicator for each Input.
- Red LED indicator for each output.
- Provides 3A fuse for overcurrent protection.
- DIN rail mountable plastic box enclosure.
- Dimensions: 145 X 90 X 40mm.
750.00 EGPIn stock
-
5A/8-Channel +ve Output Transistor Interface Module TP8
Opto-isolated 8-channel / 5 Ampere positive output transistor module for PLC industrial control.
Features :
- 8-channel positive output FET type transistor.
- Operating voltage range: 12-36V (for 48V output pls contact us).
- Maximum operating current: 5 ampere.
- All channels are opto-isolated for safety.
- Green LED indicator for power input.
- Yellow LED indicator for each Input.
- Red LED indicator for each output.
- Provides 3A fuse for overcurrent protection.
- DIN rail mountable plastic box enclosure.
- Dimensions: 145 X 90 X 40mm.
750.00 EGPIn stock
-
5V/1A DC-DC Buck Converter
5V/1A DC-DC buck converter (7-40Vin). Suitable to replace 7805 for high-efficiency requirements.
25.00 EGPIn stock
5V/1A DC-DC Buck Converter
25.00 EGP -
6-Channel Bi-directional Logic Level Converter
This module allows for safe and easy communication between devices operating at different logic levels. Typically 3.3V and 5V.
Features :
- 6-channel bi-directional logic converter suitable for bi-directional buses such as I²C, as well as uni-directional such as SPI and TTL serial communication.
- Voltage signal range: 1.8-5V.
- 2.54mm male header.
- Dimensions: 21 X 14 X 4mm ( with no pin header ).
35.00 EGPIn stock
-
6-Channel DC Power Distributor
6-Channel DC power distributor module.
Features :
- Operating voltage: 5~48 DCV.
- Maximum output current: 10A/Channel.
- Protection fuse for each channel.
- Green LED indicator for input voltage.
- Red LED indicator for each output voltage.
- 100nF filter capacitor for each output channel.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimension: 119 X 73 X 19mm.
140.00 EGP – 255.00 EGPIn stock
-
6A Dual Channel Proportional Valve Driver (PD26)
PD26 is a dual-channel industrial proportional solenoid valve driver suitable for flow and pressure control.
Features :
- Operating mode: Switching.
- Operating voltage range: 18~36V.
- Maximum output power: 150W.
- Pot-adjustable output voltage range: 12~24V.
- Maximum output current: 6A.
- Two selectable input signal ranges: (0~5V) and (0~10V).
- Two selectable output reference voltages 5V and 10V (MAX 20mA).
- Reverse polarity protection.
- Over-current and short-circuit protection.
- Green LED for power indication.
- Yellow LED for each output indication.
- Red LED for each output fault status.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimension: 122 X 112 X 30mm.
1,950.00 EGP – 2,125.00 EGPIn stock
-
6A Single Channel Proportional Valve Driver (PD16)
PD16 is a single-channel industrial proportional solenoid valve driver suitable for flow or pressure control.
Features :
- Operating mode: Switching.
- Operating voltage range: 18~36V.
- Maximum output power: 150W.
- Pot-adjustable output voltage range: 12~24V.
- Maximum output current: 6 ampere.
- Two selectable input signal ranges: (0~5V) and (0~10V).
- Two selectable output reference voltages 5V and 10V (MAX 20mA).
- Reverse polarity protection.
- Over-current and short-circuit protection.
- Green LED for power indication.
- Yellow LED for output indication.
- Red LED for output fault status.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimension: 122 X 82 X 30mm.
1,200.00 EGP – 1,345.00 EGPIn stock
-
6Axis CNC Breakout Board (VIVA+)
VIVA+ is a completely buffered CNC parallel breakout board. Supports up to 6 axes, five inputs, spindle and coolant output relays, analog output 0-10V, watchdog protection with extra output relay, and is powered from 220VAC.
VIVA+ Features :
- Completely supports MACH3 and any other soft tool that uses an LPT port.
- AC 220V input power.
- 6 axes control signals (Pulse ”PUL” and Direction “DIR”) :
- Main / Auxiliary X-axis.
- Main / Auxiliary Y-axis.
- Z-axis.
- A-axis.
- B-axis.
- C-axis.
- Control signals are TTL compatible (10mA).
- Supports five external inputs. Three inputs for axes limits (NPN proximity sensors or micro switch inputs) and two inputs for emergency stop and probe inputs (dry contact).
- All inputs are optically isolated for safety.
- Two relay outputs for spindle and coolant control (5A maximum current).
- Optional extra output relay (controlled from pin9).
- 0-10V analog output (PWM-controlled) for controlling spindle speed.
- Watchdog feature with optional relay output to ensure that all outputs are disabled during PC starting up and software program loading.
- All outputs and inputs are brought out via pluggable screw clamp connectors for flexibility.
- LED indicator for :
- Output pulse signal “PUL” (RED LED).
- Output direction signal “DIR” (Green LED).
- Output relays “spindle”, “coolant” and “watchdog” (RED LED).
- Input signals ”XL”, ”YL”, ”ZL”, ”EMR”, and ”PRB” (Yellow LED).
- Input power (RED LED).
- Dimension: 180 X 110 X 30 mm.
1,000.00 EGPIn stock
6Axis CNC Breakout Board (VIVA+)
1,000.00 EGP -
8 Digits 0.56” 7-Segment Display Module 56D800
56D800 is a serial SPI 8-digit 7-segment LED display module based on MAX7219 driver. The module is 5V powered and easy to interface to Arduino board or any microcontroller. MAX7219 driver provides individual LED segment control, display ON/OFF, and brightness control.
115.00 EGP – 125.00 EGPIn stock
8 Digits 0.56” 7-Segment Display Module 56D800
115.00 EGP – 125.00 EGP -
8 Digits 36” 7-Segment Display Module 36D800
36D800 is a serial SPI 8-digit 7-segment LED display module based on MAX7219 driver. The module is 5V powered and easy to interface to Arduino board or any microcontroller. MAX7219 driver provides individual LED segment control, display ON/OFF, and brightness control.
100.00 EGP – 110.00 EGPIn stock
8 Digits 36” 7-Segment Display Module 36D800
100.00 EGP – 110.00 EGP -
8-Channel Active High Relay Module (12V) RM812
8-Channel relay module (12V ) up to 10A rated current directly interfaced to a microcontroller or TTL logic.
150.00 EGPIn stock
-
8-Channel Active High Relay Module (24V) RM824
8-Channel relay module (24V) up to 10A rated current directly interfaced to a microcontroller or TTL logic.
150.00 EGPIn stock
-
8-Channel Active High Relay Module (5V) RM805
8-Channel relay module (5V) up to 10A rated current directly interfaced to a microcontroller or TTL logic.
150.00 EGPIn stock
-
8-Channel Bi-directional Logic Level Converter
This module allows for safe and easy communication between devices operating at different logic levels. Typically 3.3V and 5V.
Features :
- 8-channel bi-directional logic converter suitable for bi-directional buses such as I²C, as well as uni-directional such as SPI and TTL serial communication.
- Voltage signal range: 1.8-5V.
- 2.54mm male header.
- Dimensions: 27 X 14 X 4mm ( with no pin header ).
40.00 EGPIn stock
-
8-Channel DC Power Distributor
8-Channel DC power distributor module.
Features :
- Operating voltage: 5~48 DCV.
- Maximum output current: 10A/Channel.
- Protection fuse for each channel.
- Green LED indicator for input voltage.
- Red LED indicator for each output voltage.
- 100nF filter capacitor for each output channel.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimension: 143 X 72 X 20mm.
200.00 EGP – 330.00 EGPIn stock
-
8-Channel High/Low Trigger Relay Module (12V) Opto-isolated RM812I
8-Channel 12V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.
Features :
- LED indicator for each output relay.
- Both normally open and normally close are available.
- Contact current up to 10A (Resistive load).
- Isolated/non-isolated operation mode.
- Active high/low trigger operation.
- Input signals can be applied through screw terminals or pin headers for flexibility.
- Separated screw terminal power input for relay contact (isolated mode).
- Reverse polarity protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 140 X 66 X 20mm.
300.00 EGPIn stock
-
8-Channel High/Low Trigger Relay Module (24V) Opto-isolated RM824I
8-Channel 24V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.
Features :
- LED indicator for each output relay.
- Both normally open and normally close are available.
- Contact current up to 10A (Resistive load).
- Isolated/non-isolated operation mode.
- Active high/low trigger operation.
- Input signals can be applied through screw terminals or pin headers for flexibility.
- Separated screw terminal power input for relay contact ( isolated mode ).
- Reverse polarity protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 146 X 66 X 20mm.
300.00 EGPIn stock
-
8-Channel High/Low Trigger Relay Module (5V) Opto-isolated RM805I
8-Channel 5V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.
Features :
- LED indicator for each output relay.
- Both normally open and normally close are available.
- Contact current up to 10A (Resistive load).
- Isolated/non-isolated operation mode.
- Active high/low trigger operation.
- Input signals can be applied through screw terminals or pin headers for flexibility.
- Separated screw terminal power input for relay contact (isolated mode).
- Reverse polarity protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 146 X 66 X 20mm.
300.00 EGPIn stock
-
8-Channel LED Terminal
8-channel LED terminal module
Features :
- Suitable for breadboard testing.
- LEDs are active high enabled. i.e to turn a LED on apply a high logic level.
- 1K Ohm current limiting resistor.
- TTL compatible.
- Wide input voltage range 3V:12V.
20.00 EGPIn stock
8-Channel LED Terminal
20.00 EGP -
8-Channel Opto-isolated AC Input Detector Module (ACD8)
This module detects whether AC input exists.
Features :
- Input voltage range 110-250V.
- Output voltage range 3-24V.
- Input is opto-isolated for safety.
- Four (Ø 3.5mm) mounting holes for easy installation.
- LED indicator for AC input.
- Output and power pins are broken out into a pin header for easy interfacing.
- Dimensions: 96 X 51 X 15mm.
100.00 EGPIn stock
-
8-Channel Relay Module (5V/12V/24V) RM8V
8-Channel relay module (5V/12V/24V) up to 10A rated current directly interfaced to microcontroller or TTL logic.
250.00 EGPOut of stock
8-Channel Relay Module (5V/12V/24V) RM8V
250.00 EGP -
8-Channel Solid State Relay Module (5V) SSR805
8-Channel solid state relay module (5V) 240VAC/2A directly interfaced to microcontroller or TTL logic.
Features :
- Input signal: 5V (active high).
- Maximum output current: 2A.
- Maximum output voltage: 240VAC.
- 2 Ampere overcurrent protection fuse.
- LED indicator.
550.00 EGPIn stock
-
8-LED Active High Module (LP8)
LP8 is an 8-bit LED display module.
Features :
- Suitable for breadboard testing.
- LEDs are active high enabled. i.e to turn a LED on apply a high logic level.
- LP8 is a common cathode module ( all negative terminals are connected together and brought out via pin header ).
- TTL compatible.
- Wide input voltage range 3V:12V.
- Compatible with our microcontroller development kits such as Eta32, and Betamini.
20.00 EGPIn stock
-
8-LED Active Low Module (LN8)
LN8 is an 8-bit LED display module.
Features :
- Suitable for breadboard testing.
- LEDs are active LOW enabled. i.e to turn a LED ON apply a low logic level.
- LN8 is a common anode module ( all positive terminals are connected together and brought out via pin header ).
- TTL compatible.
- Wide input voltage range 3V:12V.
- Compatible with our microcontroller development kits such as Eta32, and Betamini.
20.00 EGPIn stock
-
AC/DC Filter 3A
AC/DC power filter is a bidirectional passive Low pass filter useful in filtering the output voltages of power supplies or transformers (not line input) such as filtering output 24VAC of a transformer. For AC Line filtration use our AC Line Filter.
Features :
- Maximum operating voltage: AC250V / DC400V.
- Maximum Current: 3A.
- Cut-off frequency: 5KHz.
- Operating temperature: -40 to 85°C.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 47 X 22 X 17mm.
45.00 EGPIn stock
AC/DC Filter 3A
45.00 EGP -
Arduino Mega2560 Development Kit
Comprehensive development kit that provides interfacing many devices to Mega2560 board.
0.00 EGPObsolete
Arduino Mega2560 Development Kit
0.00 EGP -
Arduino Mega2560 Project Kit
A versatile kit for easy soldering components on a test board and building fast projects based on Arduino Mega board. Double-layer PCB is used to enable soldering of components on either face.
260.00 EGP320.00 EGPIn stock
Arduino Mega2560 Project Kit
260.00 EGP320.00 EGP -
Arduino Nano Breakout Board
Arduino Nano Breakout Board.
Features :
- Arduino Nano board is based on an ATMEGA328 microcontroller.
- Arduino Nano breakout board provides pin headers to screw clamp terminals for easy access.
- Screw clamp terminals are clearly silkscreen labeled to clarify the connection.
- breakout board comes with four mounting holes for easy installation.
- Dimensions: 71 X 54 X 12mm.
110.00 EGPIn stock
Arduino Nano Breakout Board
110.00 EGP -
Arduino Nano Work Area
A versatile kit for easy soldering components on a test board and building fast projects based on Arduino Nano.
150.00 EGP240.00 EGPIn stock
Arduino Nano Work Area
150.00 EGP240.00 EGP -
Arduino Uno Development Kit
Arduino Uno Development Kit is a comprehensive development kit for Arduino Uno board that provides the most essential peripherals needed to start discovering Arduino world.
Uno Kit is designed particularly for students, beginners, and recently graduated engineers to provide easy development of Arduino-based projects.This price includes only Uno kit without accessories. To add more accessories please click below.
1,850.00 EGP2,600.00 EGPIn stock
Arduino Uno Development Kit
1,850.00 EGP2,600.00 EGP -
Arduino Uno Project Kit
Versatile kit for easy soldering components on a test board and building fast projects based on Arduino Uno.
130.00 EGP150.00 EGPIn stock
Arduino Uno Project Kit
130.00 EGP150.00 EGP -
Arduino Uno Project Kit_Ver2
A versatile kit for easy soldering components on a test board and building fast projects based on Arduino Uno board. In ver2 a double-layer PCB is used to enable soldering of components on either face. Also, an ISP header is added to comply with Arduino shields.
199.00 EGP220.00 EGPIn stock
Arduino Uno Project Kit_Ver2
199.00 EGP220.00 EGP -
ARM Development Kit (Panda)
Panda kit is an ARM development kit based on Blue Pill module which supports 32-Bit ARM Cortex-M3 microprocessor STM32F103C8T6 .
This price includes only Panda kit without accessories. To add more accessories please click below.
750.00 EGP1,150.00 EGPIn stock
ARM Development Kit (Panda)
750.00 EGP1,150.00 EGP -
ARM Development Kit (Panda+)
Panda+ kit is an ARM development kit based on Black Pill module which supports 32-bit ARM Cortex-M4 microprocessor STM32F401RCT6.
This price includes only Panda+ kit without accessories. To add more accessories please click below.
750.00 EGP1,200.00 EGPIn stock
ARM Development Kit (Panda+)
750.00 EGP1,200.00 EGP -
ARM STM32F103C Blue Pill Breakout Board
Small handy board on which you can plug your Blue Pill development board with screw terminals to get much easier to the GPIO pins.
Features :
- All Blue Pill pins are provided to 3.5mm pitch screw clamp terminals for easy access.
- Screw terminals are clearly silkscreen labeled (top and bottom) to clarify the connection.
- Four (Ø 3mm) mounting holes for easy installation.
- Dimensions: 89 X 60 X 12mm.
125.00 EGPIn stock
ARM STM32F103C Blue Pill Breakout Board
125.00 EGP -
ARM STM32F103C Blue Pill Project Kit
Blue Pill development board is based on STM32F103C8T6 32-bit Cortex-M3 RISC ARM core. This module contains the essential components and circuits to build your own ARM-based system. Blue Pill project kit is a versatile kit for easy soldering components on a test board and building fast projects based on Blue Pill development board. Double-layer PCB is used to enable components to solder on either face.
Features :
- Project Kit can be powered from any general DC adaptor 9-12V thanks to an on-board 5V regulator.
- On-board reverse polarity protection.
- All Blue Pill pin headers are exposed to screw clamp terminals for easy access.
- Large size work area 144 horizontal lines X 5 points, 36 X 3 vertical 5V lines, 36 X 3 vertical GND lines, 36 lines X 2 points (Blue pill pins in addition to power rails GND, 5V, VIN).
- Project Kit provides a CR2032 socket for a 3V battery ( no battery included ).
- Dimensions: 185 X 108 X 20mm.
250.00 EGP270.00 EGPIn stock
ARM STM32F103C Blue Pill Project Kit
250.00 EGP270.00 EGP -
ATMEGA128 Module (F128)
Pluggable small-size and versatile module based on ATMEGA128A microcontroller. Suitable for breadboard applications.
Features :
- Microcontroller: ATMEGA128.
- All I/O ports are provided through 2.54mm pitch pin header.
- Power and other special function pins are provided (5X GND, 2X VCC, AVCC, REF, PEN, and Reset).
- AVCC is generated using an LC filter for powering analog circuits.
- Oscillator frequency: 16MHz.
- SMD green LED for power indication.
- Reset switch.
- Standard 10-pin IDC connector for programming as well as a simplified 6-pin header.
- Dimensions: 84 X 35 X 18mm.
375.00 EGPIn stock
ATMEGA128 Module (F128)
375.00 EGP -
ATMEGA128 Module PCB (F128)
Versatile and small size module based on ATMEGA128A microcontroller (PCB only).
50.00 EGPOut of stock
ATMEGA128 Module PCB (F128)
50.00 EGP -
ATMEGA128 Module With Arduino Bootloader (F128B)
Pluggable small-size and versatile module based on ATMEGA128A microcontroller with Arduino bootloader. Suitable for breadboard applications.
Features :
- Microcontroller: ATMEGA128 Arduino bootloader preprogrammed.
- All I/O ports are provided through a 2.54mm pitch pin header.
- Power and other special function pins are provided (5X GND, 2X VCC, AVCC, REF, PEN, and Reset).
- AVCC is generated using an LC filter for powering analog circuits.
- Oscillator frequency: 16MHz.
- USB/Serial TTL converter (CH340) (serial communication and programming) type B micro connector.
- SMD green LED for power indication.
- Two SMD red LED indicators for TX and RX.
- Reset switch.
- Standard 10-pin IDC connector for programming as well as a simplified 6-pin header.
- Dimensions: 84 X 35 X 18mm.
400.00 EGPIn stock
-
ATMEGA8/48/88/168/328 Project Kit
ATMEGA8 Project Kit supports 28-pin DIP AVR microcontrollers such as ATMEGA8, and ATMEGA328.
Features :
- Project Kit supports ATMEGA8, ATMEGA48, ATMEGA88, ATMEGA168, and ATMEGA328.
- Project Kit can be powered from any general DC adaptor 8-20V thanks to an on-board 5V regulator.
- On-board reverse polarity protection.
- All Microcontroller pins are exposed to screw clamp terminals for easy access.
- Large size work area 144 horizontal lines X 5 points, 36 X 3 vertical 5V lines, 36 X 3 vertical GND lines, 36 lines X 2 points (Blue pill pins in addition to power rails GND, 5V, VIN).
- Project Kit includes a green LED for power indication.
- 6-Pin ICSP header socket for connecting an external programmer (no need for removing chip).
- Project Kit provides a 16MHz crystal oscillator.
- Project Kit contains a Reset switch.
- Four 7mm M-F spacers are added to keep the board out of any wires and components erroneously located under the board.
- Dimensions: 162 X 77 X 20mm.
175.00 EGPIn stock
ATMEGA8/48/88/168/328 Project Kit
175.00 EGP -
AVR Development Kit (Eta32)
Eta32 kit is an AVR development board designed particularly for students, beginners, and recently graduated engineers to provide easy development of AVR microcontroller projects.
This price includes only Eta32 kit without accessories. To add more accessories please click below.
1,500.00 EGP1,800.00 EGPIn stock
AVR Development Kit (Eta32)
1,500.00 EGP1,800.00 EGP
