4-Channel DC power distributor module.

   Features :

• Operating voltage: 5~48 DCV.
• Maximum output current: 10A/Channel.
• Protection fuse for each channel.
• Green LED indicator for input voltage.
• Red LED indicator for each output voltage.
• 100nF filter capacitor for each output channel.
• Four (Ø 3.5mm) mounting holes for easy installation.
• DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
• Dimension: 91 x 72 x 20mm.

This module is a generic 2-channel DC power fuse distributor board.

   Features :

• Operating voltage: 5~48 DCV.
• Maximum output current: 10A/channel.
• Protection fuse for each channel.
• Green LED indicator for input voltage.
• Red LED indicator for each output voltage.
• 100nF filter capacitor for each output channel.
• Four (Ø 3.5mm) mounting holes for easy installation.
• DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
• Dimension: 72 X 58 X 15mm.

PD13 is a single-channel industrial proportional solenoid valve driver suitable for flow or pressure control.

   Features :

• Operating mode: Switching.
• Operating voltage range: 18~36V.
• Maximum output power: 150W.
• Pot-adjustable output voltage range: 12~24V.
• Maximum output current: 3 ampere.
• Two selectable input signal ranges: (0~5V) and (0~10V).
• Two selectable output reference voltages 5V and 10V (MAX 20mA).
• Reverse polarity protection.
• Over-current and short-circuit protection.
• Green LED for power indication.
• Yellow LED for output indication.
• Red LED for output fault status.
• Four 3.5mm mounting holes for easy installation.
• DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
• Dimension: 107 x 80 x 27 mm.

PD16 is a single-channel industrial proportional solenoid valve driver suitable for flow or pressure control.

   Features :

• Operating mode: Switching.
• Operating voltage range: 18~36V.
• Maximum output power: 150W.
• Pot-adjustable output voltage range: 12~24V.
• Maximum output current: 6 ampere.
• Two selectable input signal ranges: (0~5V) and (0~10V).
• Two selectable output reference voltages 5V and 10V (MAX 20mA).
• Reverse polarity protection.
• Over-current and short-circuit protection.
• Green LED for power indication.
• Yellow LED for output indication.
• Red LED for output fault status.
• Four (Ø 3.5mm) mounting holes for easy installation.
• DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
• Dimension: 122 X 82 X 30mm.

This module allows for safe and easy communication between devices operating at different logic levels. Typically 3.3V and 5V.

  Features :

• 6-channel bi-directional logic converter suitable for bi-directional buses such as I²C, as well as uni-directional such as SPI and TTL serial communication.
• Voltage signal range: 1.8-5V.
• 2.54mm male header.
• Dimensions: 21 X 14 X 4mm ( with no pin header ).

This module allows for safe and easy communication between devices operating at different logic levels. Typically 3.3V and 5V.

   Features :

• 4-channel bi-directional logic converter suitable for bi-directional buses such as I²C, as well as uni-directional such as SPI and TTL serial communication.
• Voltage signal range: 1.8-5V.
• 2.54mm male header.
• Dimensions: 16 X 14 X 4mm ( with no pin header ).

FR4 PCB General project work area with DC power input and regulation.

  Features :

• Double layer FR4 PCB.
• Project Kit can be powered from any general DC adaptor 8-20V thanks to an on-board 5V regulator.
• On-board reverse polarity protection.
• 15 External input via screw clamp terminals 3.5mm pitch.
• Large size work area 148 horizontal lines X 5 points, 37 X 3 vertical 5V lines, 37 X 3 vertical GND lines, 15 lines X 2 points (in addition to power rails GND, 5V, VIN).
• Four (Ø 3.5mm) mounting holes for easy installation.
• Dimensions: 118 X 108 X 20mm.

AC 250V 10A EMI Filter.

  Features :

• Maximum operating voltage: AC250V.
• Maximum Current: 10 Ampere.
• Cut-off frequency: 5KHz.
• Four (Ø 3.5mm) mounting holes for easy installation.
• Dimension: 60 X 30 X 30mm.

DB25 male socket vertical type on PCB to block terminals and pin header facilitates solderless connection to standard serial connector. DB25 is also suitable for panel mounting and test applications.

  Features :

• DB25 pins are routed to pin headers and screw clamp terminals.
• Both terminals are labeled according to the DB25 pin number to which they are routed.
• Pin header pitch distance 2.54mm.
• Screw terminal pitch distance 3.5mm.
• Four (Ø 4mm) mounting holes for easy installation.
• Dimensions: 65 X 45 X 25mm.

8-Channel relay module (24V) up to 10A rated current directly interfaced to a microcontroller or TTL logic.

4-Channel relay module (24V) up to 10A rated current directly interfaced to a microcontroller or TTL logic.

1-Channel 5V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.

  Features :

• LED indicator for each output relay.
• Both normally open and normally close are available.
• Contact current up to 10A (Resistive load).
• Isolated/non-isolated operation mode.
• Active high/low trigger operation.
• Input signals can be applied through screw terminals or pin headers for flexibility.
• Separated screw terminal power input for relay contact (isolated mode).
• Reverse polarity protection.
• Four (Ø 3.5mm) mounting holes for easy installation.
• Dimension: 66 X 30 X 20mm.

4-Channel 24V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.

  Features :

• LED indicator for each output relay.
• Both normally open and normally close are available.
• Contact current up to 10A (Resistive load).
• Isolated/non-isolated operation mode.
• Active high/low trigger operation.
• Input signals can be applied through screw terminals or pin headers for flexibility.
• Separated screw terminal power input for relay contact (isolated mode).
• Reverse polarity protection.
• Four (Ø 3.5mm) mounting holes for easy installation.
• Dimension: 80 X 68 X 20mm.

1-Channel 24V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.

  Features :

• LED indicator for each output relay.
• Both normally open and normally close are available.
• Contact current up to 10A (Resistive load).
• Isolated/non-isolated operation mode.
• Active high/low trigger operation.
• Input signals can be applied through screw terminals or pin headers for flexibility.
• Separated screw terminal power input for relay contact (isolated mode).
• Reverse polarity protection.
• Four (Ø 3.5mm) mounting holes for easy installation.
• Dimension: 66 X 30 X 20mm.

1-Channel 12V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.

  Features :

• LED indicator for each output relay.
• Both normally open and normally close are available.
• Contact current up to 10A (Resistive load).
• Isolated/non-isolated operation mode.
• Active high/low trigger operation.
• Input signals can be applied through screw terminals or pin headers for flexibility.
• Separated screw terminal power input for relay contact (isolated mode).
• Reverse polarity protection.
• Four (Ø 3.5mm) mounting holes for easy installation.
• Dimension: 66 X 30 X 20mm.

The photo-reflector consists of a GaAs infrared light-emitting diode and a silicon planar phototransistor. When an object is placed right in front of the sensor, the reflective infrared light emitted from the emitter will be picked up by the phototransistor and then output logical HIGH or logical LOW according to the distance between the reflection surface and the sensor.

  Features :

• Using a wide voltage LM393 comparator.
• The working voltage of 3.3V-5V.
• Maximum output sink current 10mA.
• Operating range 0~5mm.
• Output is active low i.e an interruption produces a low output (LED is activated).
• Two (Ø 3.5mm) mounting holes for easy installation.
• It is compatible with Arduino board.
• Dimension: 38 X 17 X 17mm.

A photo interrupter sensor consists of a light-emitting element (IR LED) and a light-receiving element (phototransistor) aligned facing each other. It works by detecting light interruption when a target object comes between both elements, acting as an optical switch. This changes the output of the sensor.

  Features :

• USB a wide voltage comparator LM393.
• Operating voltage: 3.3 ~ 5V.
• Active low output i.e an interruption produces a low output (LED is activated).
• Maximum output sink current: 10mA.
• 5mm slot width.
• Two (Ø 3.5mm) mounting holes for easy installation.
• Dimensions: 26 X 21 X 6mm.

USB type B female socket on PCB to header suitable for panel mounting and test applications.

DB25 female socket on PCB to block terminals and pin header facilitates solderless connection to standard serial connector DB25 and is also suitable for breadboard test applications.

  Features :

• DB25 pins are routed to pin headers and screw clamp terminals.
• Both terminals are labeled according to the DB25 pin number to which they are routed.
• Pin header pitch distance 2.54mm.
• Screw terminal pitch distance 3.5mm.
• Four (Ø 3.5mm) mounting holes for easy installation.
• Dimensions: 93 X 33 X 15mm.

DB9 male socket on PCB to block terminals and pin header facilitates solderless connection to standard serial connector DB9 and is also suitable for breadboard test applications.

   Features :

• DB9 pins are routed to pin headers and screw clamp terminals.
• Both terminals are labeled according to the DB9 pin number to which they are routed.
• Pin header pitch distance 2.54mm.
• Screw terminal pitch distance 3.5mm.
• Two (Ø 3.5mm) mounting holes for easy installation.
• Dimensions: 35 X 33 X 15mm.

DB9 female socket on PCB to block terminals and pin header facilitates solderless connection to standard serial connector DB9 and is also suitable for breadboard test applications.

   Features :

• DB9 pins are routed to pin headers and screw clamp terminals.
• Both terminals are labeled according to the DB9 pin number to which they are routed.
• Pin header pitch distance 2.54mm.
• Screw terminal pitch distance 3.5mm.
• Two (Ø 3.5mm) mounting holes for easy installation.
• Dimensions: 35 X 33 X 15mm.