-
2-Channel Wireless Relay Module nRF24L01+ (RM2N)
The RM2N is a 2-channel wireless relay module based on the nRF24L01+ chip from Nordic Semiconductor. The nRF24L01 module is designed to operate in the global 2.4GHz ISM frequency band and uses GFSK modulation to transmit data. The card is well-protected, filtered, and easy to install. RM2N outputs can drive loads up to 10A (resistive loads).
Features:
- Based on nRF24L01+ module.
- On-board 3.3V,5V regulator.
- Power input is filtered for noise reduction.
- LED for power indication.
- Operating voltage DC12V.
- Two output relays with red LED indicators.
- Both normal open and normal close terminals are available.
- Relay outputs are available through 5mm 2-pin K128 screw clamp terminals.
- Easy configuration and test.
- Reset push button switch is included.
- DIN Rail mountable.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 100 X 50 X 18mm.
280.00 EGPIn stock
-
4-Channel Solid State Relay Module (5V) SSR405
4-Channel solid state relay module (5V) 240VAC/2A directly interfaced to microcontroller or TTL logic.
Features :
- Input signal: 5V (active high).
- Maximum output current: 2A.
- Maximum output voltage: 240VAC.
- 2 Ampere overcurrent protection fuse.
- LED indicator.
280.00 EGPIn stock
-
8-Channel Non-Isolated Positive Triggered Relay Module (RM8VE)
8-Channel 5V relay module with wide 5–40V input range, LM2576 power regulation, ULN2803 driver, and screw terminals for easy wiring.
Features :
- 8-Channel relay module using T73 relays (rated 10A for resistive loads; recommended ≤ 5A for inductive loads).
- Wide input voltage range: 5V to 40V selectable via 3-pin jumper.
- 5–7V mode: Direct input to relays.
- 7–40V mode: Onboard LM2576 buck converter outputs stable 5V.
- Relay coil voltage: 5V for all channels.
- Compatible trigger signal range: 3V to 24V.
- Integrated ULN2803 driver IC with built-in flyback diodes for relay protection.
- Additional reverse polarity protection diode on power input.
- Each relay has LED indicator for status visualization.
- Output terminals: 3-pin screw connectors (NC, COM, NO) per relay.
- Input & power via 10-pin screw terminal (2 power pins + IN1 to IN8).
- High-quality PCB with white silkscreen legend for easy wiring identification.
- Four mounting holes (Ø 3.5 mm) for secure installation.
250.00 EGPIn stock
-
8-Channel Relay Module (5V/12V/24V) RM8V
8-Channel relay module (5V/12V/24V) up to 10A rated current directly interfaced to microcontroller or TTL logic.
250.00 EGPOut of stock
8-Channel Relay Module (5V/12V/24V) RM8V
250.00 EGP -
8-Channel Active High Relay Module (24V) RM824
8-Channel relay module (24V) up to 10A rated current directly interfaced to a microcontroller or TTL logic.
225.00 EGPIn stock
-
8-Channel Active High Relay Module (5V) RM805
8-Channel relay module (5V) up to 10A rated current directly interfaced to a microcontroller or TTL logic.
225.00 EGPIn stock
-
8-Channel Active High Relay Module (12V) RM812
8-Channel relay module (12V ) up to 10A rated current directly interfaced to a microcontroller or TTL logic.
225.00 EGPIn stock
-
8-Channel High/Low Trigger Relay Module (24V) Opto-isolated RM824I
8-Channel 24V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.
Features :
- LED indicator for each output relay.
- Both normally open and normally close are available.
- Contact current up to 10A (Resistive load).
- Isolated/non-isolated operation mode.
- Active high/low trigger operation.
- Input signals can be applied through screw terminals or pin headers for flexibility.
- Separated screw terminal power input for relay contact ( isolated mode ).
- Reverse polarity protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 146 X 66 X 20mm.
220.00 EGPIn stock
-
ARM STM32F103C Blue Pill Project Kit
Blue Pill development board is based on STM32F103C8T6 32-bit Cortex-M3 RISC ARM core. This module contains the essential components and circuits to build your own ARM-based system. Blue Pill project kit is a versatile kit for easy soldering components on a test board and building fast projects based on Blue Pill development board. Double-layer PCB is used to enable components to solder on either face.
Features :
- Project Kit can be powered from any general DC adaptor 9-12V thanks to an on-board 5V regulator.
- On-board reverse polarity protection.
- All Blue Pill pin headers are exposed to screw clamp terminals for easy access.
- Large size work area 144 horizontal lines X 5 points, 36 X 3 vertical 5V lines, 36 X 3 vertical GND lines, 36 lines X 2 points (Blue pill pins in addition to power rails GND, 5V, VIN).
- Project Kit provides a CR2032 socket for a 3V battery ( no battery included ).
- Dimensions: 185 X 108 X 20mm.
220.00 EGPIn stock
ARM STM32F103C Blue Pill Project Kit
220.00 EGP -
16-Channel Relay Module (12V) RM1612
16 Channel relay module (12V) up to 10A rated current directly interfaced to microcontroller or TTL logic.
220.00 EGP260.00 EGPObsolete
16-Channel Relay Module (12V) RM1612
220.00 EGP260.00 EGP -
8-Channel High/Low Trigger Relay Module (12V) Opto-isolated RM812I
8-Channel 12V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.
Features :
- LED indicator for each output relay.
- Both normally open and normally close are available.
- Contact current up to 10A (Resistive load).
- Isolated/non-isolated operation mode.
- Active high/low trigger operation.
- Input signals can be applied through screw terminals or pin headers for flexibility.
- Separated screw terminal power input for relay contact (isolated mode).
- Reverse polarity protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 140 X 66 X 20mm.
220.00 EGPIn stock
-
8-Channel High/Low Trigger Relay Module (5V) Opto-isolated RM805I
8-Channel 5V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.
Features :
- LED indicator for each output relay.
- Both normally open and normally close are available.
- Contact current up to 10A (Resistive load).
- Isolated/non-isolated operation mode.
- Active high/low trigger operation.
- Input signals can be applied through screw terminals or pin headers for flexibility.
- Separated screw terminal power input for relay contact (isolated mode).
- Reverse polarity protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 146 X 66 X 20mm.
220.00 EGPIn stock
-
PIC Project Kit
PIC Project kit supports 40-pin DIP PIC microcontrollers such as PIC6F877A, 18F452, and more.
Features :
- Project Kit can be powered from any general DC adaptor 8-20V thanks to an on-board 5V regulator.
- On-board reverse polarity protection.
- All microcontroller ports are exposed to screw clamp terminals for external use.
- Large size work area 136 horizontal lines X 5 points, 34 X 3 vertical 5V lines, 34 X 3 vertical GND lines, 34 lines X 2 points (Raspberry Pi Pico pins in addition to power rails GND, 5V, VIN).
- Project Kit contains a Reset push button switch.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 181 X 105 X 21mm.
220.00 EGPIn stock
PIC Project Kit
220.00 EGP -
AVR Project Kit
AVR Project Kit supports 40-pin DIP AVR microcontrollers ATMEGA8535, ATMEGA16, and ATMEGA32.
Features :
- Project Kit can be powered from any general DC adaptor 8-20V thanks to an on-board 5V regulator.
- On-board reverse polarity protection.
- All microcontroller ports are exposed to screw clamp terminals for external use.
- Large size work area 136 horizontal lines X 5 points, 34 X 3 vertical 5V lines, 34 X 3 vertical GND lines, 34 lines X 2 points (Raspberry Pi Pico pins in addition to power rails GND, 5V, VIN).
- Project Kit contains a Reset push button switch.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 181 X 105 X 21mm.
220.00 EGPIn stock
AVR Project Kit
220.00 EGP -
Raspberry Pi Pico Work Area
Raspberry Pi Pico work area.
Features :
- Project Kit can be powered from any general DC adaptor 8-20V thanks to an on-board 5V regulator.
- On-board reverse polarity protection.
- All Raspberry Pi Pico ports are exposed to screw clamp terminals for external use.
- Large size work area 136 horizontal lines X 5 points, 34 X 3 vertical 5V lines, 34 X 3 vertical GND lines, 34 lines X 2 points (Raspberry Pi Pico pins in addition to power rails GND, 5V, VIN).
- Project Kit contains a Reset push button switch.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 175 X 99 X 20mm.
210.00 EGPIn stock
Raspberry Pi Pico Work Area
210.00 EGP -
Arduino Uno Work Area
A versatile kit for easy soldering components on a test board and building fast projects based on Arduino Uno board. In ver2 a double-layer PCB is used to enable soldering of components on either face. Also, an ISP header is added to comply with Arduino shields.
200.00 EGPIn stock
Arduino Uno Work Area
200.00 EGP -
Project Work Area
FR4 PCB General project work area with DC power input and regulation.
Features :
- Double layer FR4 PCB.
- Project Kit can be powered from any general DC adaptor 8-20V thanks to an on-board 5V regulator.
- On-board reverse polarity protection.
- 15 External input via screw clamp terminals 3.5mm pitch.
- Large size work area 148 horizontal lines X 5 points, 37 X 3 vertical 5V lines, 37 X 3 vertical GND lines, 15 lines X 2 points (in addition to power rails GND, 5V, VIN).
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 118 X 108 X 20mm.
190.00 EGPIn stock
Project Work Area
190.00 EGP -
8-Channel DC Power Distributor
8-Channel DC power distributor module.
Features :
- Operating voltage: 5~48 DCV.
- Maximum output current: 10A/Channel.
- Protection fuse for each channel.
- Green LED indicator for input voltage.
- Red LED indicator for each output voltage.
- 100nF filter capacitor for each output channel.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimension: 143 X 72 X 20mm.
175.00 EGPIn stock
8-Channel DC Power Distributor
175.00 EGP -
ATMEGA8/48/88/168/328 Project Kit
ATMEGA8 Project Kit supports 28-pin DIP AVR microcontrollers such as ATMEGA8, and ATMEGA328.
Features :
- Project Kit supports ATMEGA8, ATMEGA48, ATMEGA88, ATMEGA168, and ATMEGA328.
- Project Kit can be powered from any general DC adaptor 8-20V thanks to an on-board 5V regulator.
- On-board reverse polarity protection.
- All Microcontroller pins are exposed to screw clamp terminals for easy access.
- Large size work area 144 horizontal lines X 5 points, 36 X 3 vertical 5V lines, 36 X 3 vertical GND lines, 36 lines X 2 points (Blue pill pins in addition to power rails GND, 5V, VIN).
- Project Kit includes a green LED for power indication.
- 6-Pin ICSP header socket for connecting an external programmer (no need for removing chip).
- Project Kit provides a 16MHz crystal oscillator.
- Project Kit contains a Reset switch.
- Four 7mm M-F spacers are added to keep the board out of any wires and components erroneously located under the board.
- Dimensions: 162 X 77 X 20mm.
175.00 EGPIn stock
ATMEGA8/48/88/168/328 Project Kit
175.00 EGP -
USBasp (Type B) AVR Programmer
USBasp is an in-circuit programmer for Atmel AVR microcontrollers.
Features :
- USB B female-type socket.
- 6-pin Flat cable is included.
- Green LED for normal status.
- Red LED for busy status.
- Support low-clock speed programming (Jumper setting).
- Target device can be USB-biased (Jumper setting).
- Easy firmware updating (Jumper setting).
- Support both 6-pin header and 10-pin IDC socket for flexibility.
This price includes only a USBasp programmer without USB cable. To add a USB cable please click below.
160.00 EGPIn stock
USBasp (Type B) AVR Programmer
160.00 EGP -
USB to RS485 Serial Converter Module
This USB to RS485 converter is based on CH340 USB to serial IC. It provides a virtual serial port over a USB 2.0 port. Serial signals are provided in RS485 level to screw clamp terminal. Once you have installed the drivers, the module will appear as a normal serial COM port on your computer, making it compatible with most terminal programs and development environments.
Features:
- Provides virtual serial port over USB2.0 port.
- MAX487 transceiver.
- Supports Win 7, 8, 10, and 11 32/64-bit.
- B-type socket full-speed 2.0 USB interface.
- USB-powered (5V).
- Half-duplex serial mode.
- RS485 data rate up to 250 Kbps.
- Serial baud rate up to 2 Mbps.
- Up to 128 nodes on bus.
- TVS protection ±30 KV ESD.
- PTC (JZ) for overcurrent fault protection.
- 120 Ohm terminal resistor included.
- Red LED indicator for Rx and Tx signals.
- Green LED for power status.
- One (Ø 3.5mm) mounting hole for easy installation.
- Dimensions: 49 X 21 X 15 mm.
150.00 EGPOut of stock
USB to RS485 Serial Converter Module
150.00 EGP -
USBasp (Type A) AVR Programmer
Compact USB programmer for AVR microcontrollers with voltage selection, speed jumper, and clear status indication.
Features :
- Supported Devices: Compatible with most AVR 8-bit microcontrollers such as ATmega8, ATmega16, ATmega32, ATmega328, ATmega128, ATtiny series, and AT90 series.
- USB Type-A Connector: Direct connection to PC without extra cables.
- Supports low-clock speed programming via jumper setting.
- Target Power Selection: 3-pin header with jumper to supply the target device with 5V, 3.3V, or completely disconnect power.
-
Flexible Connectivity: Two options for connecting to the target device:
-
6-pin XH cable header.
-
10-pin IDC socket.
-
- 10-Pin IDC cable is included.
- Green LED: Indicates normal operation.
- Red LED: Indicates programming in progress (busy).
- Firmware Upgradable: Dedicated PRG header for easy firmware updates.
-
Wide Compatibility: Supports various AVR microcontrollers and works seamlessly with tools like AVRDUDE.
-
Compact PCB Design: Small form factor for convenient use in different projects.
- Dimensions(L X W X H): 75X20X12 mm (including connectors)
150.00 EGPIn stock
USBasp (Type A) AVR Programmer
150.00 EGP -
4-Channel High/Low Trigger Relay Module (24V) Opto-isolated RM424I
4-Channel 24V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.
Features :
- LED indicator for each output relay.
- Both normally open and normally close are available.
- Contact current up to 10A (Resistive load).
- Isolated/non-isolated operation mode.
- Active high/low trigger operation.
- Input signals can be applied through screw terminals or pin headers for flexibility.
- Separated screw terminal power input for relay contact (isolated mode).
- Reverse polarity protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 80 X 68 X 20mm.
150.00 EGPIn stock
-
3A / 2-Channel +ve Output Transistor Interface Module TP2
Opto-isolated 2-channel / 3 Ampere positive output transistor module for PLC industrial control.
Features :
- 2-channel positive output FET type transistor.
- Operating voltage range: 12-36V (for 48V output pls contact us).
- Maximum operating current: 3A.
- All channels are opto-isolated for safety.
- Green LED indicator for power input.
- Yellow LED indicator for each Input.
- Red LED indicator for each output.
- Provides 3A fuse for overcurrent protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 90 X 53 X 22mm.
150.00 EGPIn stock
-
3A / 2-Channel -ve Output Transistor Interface Module TN2
Opto-isolated 2-channel / 3 Ampere negative output transistor module for PLC industrial control.
Features :
- 2-channel negative output FET type transistor.
- Operating voltage range: 12-36V (for 48V output pls contact us).
- Maximum operating current: 3A.
- All channels are opto-isolated for safety.
- Green LED indicator for power input.
- Yellow LED indicator for each Input.
- Red LED indicator for each output.
- Provides 3A fuse for overcurrent protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 90 X 53 X 22mm.
150.00 EGPIn stock
-
2-Channel Solid State Relay Module (5V) SSR205
2-Channel solid state relay module (5V) 240VAC/2A directly interfaced to microcontroller or TTL logic.
Features :
- Input signal: 5V (active high).
- Maximum output current: 2A.
- Maximum output voltage: 240VAC.
- 2 Ampere overcurrent protection fuse.
- LED indicator.
150.00 EGPIn stock
-
SPI AVR Programmer Extension Board
SPI AVR Programmer Extension Board.
Supported Chips :
- ATMEGA16 / ATMEGA32 / ATMEGA8535 / ATMEGA8.
- ATMEGA168 / ATMEGA328 / ATMEGA48 / ATMEGA88.
- ATMEGA644 / ATMEGA324 / ATMEGA164 / ATMEGA61 / ATMEGA62.
- ATMEGA8515 / AT90S4434 / AT90S8535 / AT90S2333 / AT90S4433.
- AT90S2323 / AT90S2343 / AT90S1200 / AT90S2313.
- AT90S8515 / AT90S4414 / ATTINY11 / ATTINY12.
- ATTINY13 / ATTINY15 / ATTINY25 / ATTINY45.
- ATTINY85 / ATTINY2313 / ATTINY24 / ATTINY44 / ATTINY84.
150.00 EGPIn stock
SPI AVR Programmer Extension Board
150.00 EGP -
Arduino Nano Work Area
A versatile kit for easy soldering components on a test board and building fast projects based on Arduino Nano.
150.00 EGPIn stock
Arduino Nano Work Area
150.00 EGP -
4-Channel High/Low Trigger Relay Module (12V) Opto-isolated RM412I
4-Channel 12V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.
Features :
- LED indicator for each output relay.
- Both normally open and normally close are available.
- Contact current up to 10A (Resistive load).
- Isolated/non-isolated operation mode.
- Active high/low trigger operation.
- Input signals can be applied through screw terminals or pin headers for flexibility.
- Separated screw terminal power input for relay contact (isolated mode).
- Reverse polarity protection.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 80 X 66 X 20mm.
150.00 EGPIn stock
-
4-Channel High/Low Trigger Relay Module (5V) Opto-isolated RM405I
4-Channel 5V relay module up to 10A rated current active high/low trigger directly interfaced to microcontroller or TTL logic with opto-isolation.
Features :
- LED indicator for each output relay.
- Both normally open and normally close are available.
- Contact current up to 10A (Resistive load).
- Isolated/non-isolated operation mode.
- Active high/low trigger operation.
- Input signals can be applied through screw terminals or pin headers for flexibility.
- Separated screw terminal power input for relay contact (isolated mode).
- Reverse polarity protection.
- Four mounting holes for easy installation.
- Dimension: 80X66X20 mm.
150.00 EGPIn stock
-
4-Channel Relay Module (5V/12V/24V) RM4V
4-Channel relay module (5V/12V/24V) up to 10A rated current directly interfaced to microcontroller or TTL logic .
150.00 EGPIn stock
4-Channel Relay Module (5V/12V/24V) RM4V
150.00 EGP -
Real Time Clock Module (DS3231 & 4K Memory 24C32)
This RTC module is based on the clock chip DS1307 that provides seconds, minutes, hours, day, date, month, and year information.
Features :
- Operating voltage 5V.
- Supports the 24-hour or 12-hour format with an AM/PM indicator.
- Interface: I2C.
- On-board 4K I2C serial EEPROM.
- On-board CR2032 3V lithium battery.
- Two (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 34 X 24 X 10mm.
140.00 EGPIn stock
-
6-Channel DC Power Distributor
6-Channel DC power distributor module.
Features :
- Operating voltage: 5~48 DCV.
- Maximum output current: 10A/Channel.
- Protection fuse for each channel.
- Green LED indicator for input voltage.
- Red LED indicator for each output voltage.
- 100nF filter capacitor for each output channel.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimension: 119 X 73 X 19mm.
140.00 EGPIn stock
6-Channel DC Power Distributor
140.00 EGP -
Arduino Uno Breakout Board
Arduino Uno Breakout Board.
135.00 EGPIn stock
Arduino Uno Breakout Board
135.00 EGP -
4-Channel Active High Relay Module (24V) RM424
4-Channel relay module (24V) up to 10A rated current directly interfaced to a microcontroller or TTL logic.
135.00 EGPIn stock
-
4-Channel Active High Relay Module (5V) RM405
4-Channel relay module (5V) up to 10A rated current directly interfaced to a microcontroller or TTL logic.
135.00 EGPIn stock
-
4-Channel Active High Relay Module (12V) RM412
4-Channel relay module (12V ) up to 10A rated current directly interfaced to a microcontroller or TTL logic.
135.00 EGPIn stock
-
8-Channel Isolation Module
8-channel opto-isolated module suitable for voltage level converting.
Features :
- Two selectable Input control signal ranges (3-12V and 9-24V).
- Output signal range: 3-24V.
- LED indicator for each input.
- Dedicated 2-pin screw clamp terminal for each input and output.
- Output can drive high or low-triggered load.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimensions: 129 X 50 X 17mm.
130.00 EGPIn stock
8-Channel Isolation Module
130.00 EGP -
10A AC Line Filter
AC 250V 10A EMI Filter.
Features :
- Maximum operating voltage: AC250V.
- Maximum Current: 10 Ampere.
- Cut-off frequency: 5KHz.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 60 X 30 X 30mm.
130.00 EGPIn stock
10A AC Line Filter
130.00 EGP -
Arduino Uno Project Kit
Versatile kit for easy soldering components on a test board and building fast projects based on Arduino Uno.
130.00 EGPIn stock
Arduino Uno Project Kit
130.00 EGP -
USB to RS232 Serial Module (CH340) B-Type USB Socket to DB9/Header
This USB to RS232 converter is based on CH340 USB to serial IC. It provides a virtual serial port over USB 2.0 port. Serial signals are provided in RS232 level to both header pins and standard DB9 male socket. Once you have installed the drivers the module will appear as a normal serial COM port on your computer making it compatible with most terminal programs and development environments.
Features :
- Provides virtual serial port over USB2.0 port.
- Supports Win7, Win8, Win10 32/64Bit.
- B-type socket Full speed 2.0 USB interface.
- Supports up to 2Mbps baud rates.
- RS232 signals are provided to both pin header and Standard DB9 socket for flexibility.
- Self-powered from USB 5V.
- Supports Rx, Tx, DTR, and DSR signals.
- Red LEDs indicator for Rx and Tx signals.
- Green LED for power status.
- 5V from USB is available to header pin for supplying external devices (100mA MAX).
- Two 3mm mounting holes for easy installation.
- Dimensions: 64X33X19 mm.
120.00 EGPIn stock
-
3+3+2 Digits 0.56” 7-Segment Display Module 56D332
56D332 is a serial SPI 3+3+2-digit 7-segment LED display module based on MAX7219 driver. The module is 5V powered and easy to interface to Arduino board or any microcontroller. MAX7219 driver provides individual LED segment control, display ON/OFF, and brightness control.
110.00 EGP – 115.00 EGPIn stock
3+3+2 Digits 0.56” 7-Segment Display Module 56D332
110.00 EGP – 115.00 EGP -
4+4 Digits 0.56” 7-Segment Display Module 56D440
56D440 is a serial SPI 4+4-digit 7-segment LED display module based on MAX7219 driver. The module is 5V powered and easy to interface to Arduino board or any microcontroller. MAX7219 driver provides individual LED segment control, display ON/OFF, and brightness control.
110.00 EGP – 115.00 EGPIn stock
4+4 Digits 0.56” 7-Segment Display Module 56D440
110.00 EGP – 115.00 EGP -
8 Digits 0.56” 7-Segment Display Module 56D800
56D800 is a serial SPI 8-digit 7-segment LED display module based on MAX7219 driver. The module is 5V powered and easy to interface to Arduino board or any microcontroller. MAX7219 driver provides individual LED segment control, display ON/OFF, and brightness control.
110.00 EGP – 115.00 EGPIn stock
8 Digits 0.56” 7-Segment Display Module 56D800
110.00 EGP – 115.00 EGP -
Real Time Clock Module (DS3231)
This RTC module is based on the clock chip DS1307 that provides seconds, minutes, hours, day, date, month, and year information.
Features :
- Operating voltage: 5V.
- Supports the 24-hour or 12-hour format with an AM/PM indicator.
- Interface: I2C.
- On-board CR2032 3V lithium battery.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 33 X 30 X 10mm.
110.00 EGPIn stock
Real Time Clock Module (DS3231)
110.00 EGP -
4 Digits 0.56” 7-Segment Display Module 56D400
56D400 is a serial SPI 4-digit 7-segment LED display module based on MAX7219 driver. The module is 5V powered and easy to interface to Arduino board or any microcontroller. MAX7219 driver provides individual LED segment control, display ON/OFF, and brightness control.
100.00 EGP – 105.00 EGPIn stock
4 Digits 0.56” 7-Segment Display Module 56D400
100.00 EGP – 105.00 EGP -
ARM STM32F401 Black Pill Breakout Board
Small handy board on which you can plug your Black Pill development board with screw terminals to get much easier to the GPIO pins.
Features :
- All Black Pill pins are provided to 3.5mm pitch screw clamp terminals for easy access.
- Screw terminals are clearly silkscreen labeled (top and bottom) to clarify the connection.
- Four (Ø 3mm) mounting holes for easy installation.
- Dimensions: 89 x 60 x 12 mm.
100.00 EGPIn stock
ARM STM32F401 Black Pill Breakout Board
100.00 EGP -
30A Current Sensor Module (ACS712)
30A Current Sensor Module (ACS712).
Features:
- Operating voltage: 5V.
- Green LED for power indication.
- Input interface 7.5mm screw clamp terminal.
- Power and output signal interface: 2.54mm male pin header.
- Maximum current: 30A.
- One (Ø 3.5mm) mounting hole for easy installation.
- Dimension: 34 X 15 X 14mm.
100.00 EGPIn stock
30A Current Sensor Module (ACS712)
100.00 EGP
